Microstructure and Residual Stress of In-situ Synthesized (TiC+TiB)/Ti Composites
摘 要
通过钛、石墨、二硼化钛间的原位反应,并经真空熔炼、锻造、退火后制备得到了不同增强体(TiC,TiB)含量的(TiC+TiB)/Ti复合材料,研究了其物相组成与显微组织,并测试了其残余应力,通过建立残余应力数值拟合公式分析了微观残余应力之间的耦合关系。结果表明:钛基复合材料的基体组织为变形α组织,增强体分布均匀,其中TiC呈等轴状和不规则状,TiB呈短纤维状并沿锻造方向排列;TiC和TiB与钛基体因热膨胀系数不同而产生的微观残余应力分别为拉应力和压应力,当TiC与TiB体积比为1:1时微观残余应力的耦合系数为2.0。
Abstract
(TiC+TiB)/Ti composites with different reinforcement (TiC, TiB) content were prepared by in-situ synthesis of Ti, graphite and TiB2 followed by vacuum melting,forging and annealing. The phase composition and microstructure were studied and the residual stresses were measured. Numerical simulation formulas of residual stresses were also established to analyze the coupling relationship between micro residual stresses. The results show that the Ti substrate in Ti matrix composites was composed of deformed α-microstructure and the reinforcements dispersed evenly. TiC had equiaxed or irregular shapes while TiB was short fibrous and distributed along forging direction. Mirco residual stresses generated by the mismatch of coefficients of thermal expansion between TiC or TiB and Ti substrate were tension and compression stresses, respectively. When the volume ratio of TiC to TiB was 1:1, the coupling coefficient of the micro residual stresses was 2.0.
中图分类号 TB333 DOI 10.11973/jxgccl201710004
所属栏目 试验研究
基金项目 国家自然科学基金资助项目(51371114);国家重点基础研究发展“973”计划项目(2012CB619600)
收稿日期 2016/3/26
修改稿日期 2017/9/6
网络出版日期
作者单位点击查看
备注孟嘉琳(1990-),女,陕西西安人,硕士研究生
引用该论文: MENG Jialin,GUO Xianglong,LÜ,Weijie,QIN Jining,WANG Liqiang,MAO Jianwei,ZHANG Di. Microstructure and Residual Stress of In-situ Synthesized (TiC+TiB)/Ti Composites[J]. Materials for mechancial engineering, 2017, 41(10): 15~19
孟嘉琳,郭相龙,吕维洁,覃继宁,王立强,毛建伟,张荻. 原位自生(TiC+TiB)/Ti复合材料的显微组织与残余应力[J]. 机械工程材料, 2017, 41(10): 15~19
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】耿都都, 严春妍, 纳学洋,等. X100管线钢的焊接冷裂纹敏感性分析[J]. 电焊机, 2015, 45(8):150-153.
【2】DONG C F, LIU Z Y, LI X G, et al. Effects of hydrogen-charging on the susceptibility of X100 pipeline steel to hydrogen-induced cracking[J]. International Journal of Hydrogen Energy, 2009, 34(24):9879-9884.
【3】JIANG Q M, ZHANG X Q, CHEN L Q. Weldability of 1000 MPa grade ultra-low carbon bainitic steel[J]. Journal of Iron and Steel Research, International, 2016, 23(7):705-710.
【4】RINGINEN D A, CHASTUKHIN A V, KHADEEV G E, et al. A weldability study of steel of strength class X100[J]. Metallurgist, 2014, 57(11):1112-1119.
【5】KHRIPLIVYI A A, ZHDANOV I M, GORDONNYI V G, et al. Evaluating the cold cracking resistance of welded joints in clad steels[J]. Welding International, 1987, 1(5):422-425.
【6】任芝兰, 邓彬. HG70低合金高强钢的焊接冷裂敏感性及其焊接预热温度的拟定[J]. 热加工工艺, 2009, 38(23):152-154.
【7】吴冰, 陈辉. X80管线钢的焊接冷裂纹试验[J]. 电焊机, 2008, 38(10):66-69.
【8】李亚娟, 贾鹏, 李午申,等. X80管线钢焊接冷裂敏感性判据的建立[J]. 焊接学报, 2012, 33(4):85-88.
【9】常智渊. 超低碳微合金X100管线钢焊接性的研究[D]. 沈阳:东北大学, 2013.
【10】谭长瑛, 周昭伟, 葛学廉. 插销试件合理缺口深度的探讨[J]. 焊接学报, 1981,2(4):10-17.
【11】张君,牛辉. X100管线钢冷裂敏感性研究[J].焊管,2012(11):22-26.
【12】张文钺, 祝美丽, 秦伯雄,等. 焊接冷裂敏感性硬化因子与氢扩散因子的探讨[J]. 兵器材料科学与工程, 1991(12):8-15.
【13】李亚江, 王娟. 焊接缺陷分析与对策[M]. 北京:化学工业出版社, 2014.
【14】徐学利, 张福平, 黄景鹏. X100管线钢焊接冷裂纹敏感性研究[J]. 焊接技术, 2016(8):25-28.
【2】DONG C F, LIU Z Y, LI X G, et al. Effects of hydrogen-charging on the susceptibility of X100 pipeline steel to hydrogen-induced cracking[J]. International Journal of Hydrogen Energy, 2009, 34(24):9879-9884.
【3】JIANG Q M, ZHANG X Q, CHEN L Q. Weldability of 1000 MPa grade ultra-low carbon bainitic steel[J]. Journal of Iron and Steel Research, International, 2016, 23(7):705-710.
【4】RINGINEN D A, CHASTUKHIN A V, KHADEEV G E, et al. A weldability study of steel of strength class X100[J]. Metallurgist, 2014, 57(11):1112-1119.
【5】KHRIPLIVYI A A, ZHDANOV I M, GORDONNYI V G, et al. Evaluating the cold cracking resistance of welded joints in clad steels[J]. Welding International, 1987, 1(5):422-425.
【6】任芝兰, 邓彬. HG70低合金高强钢的焊接冷裂敏感性及其焊接预热温度的拟定[J]. 热加工工艺, 2009, 38(23):152-154.
【7】吴冰, 陈辉. X80管线钢的焊接冷裂纹试验[J]. 电焊机, 2008, 38(10):66-69.
【8】李亚娟, 贾鹏, 李午申,等. X80管线钢焊接冷裂敏感性判据的建立[J]. 焊接学报, 2012, 33(4):85-88.
【9】常智渊. 超低碳微合金X100管线钢焊接性的研究[D]. 沈阳:东北大学, 2013.
【10】谭长瑛, 周昭伟, 葛学廉. 插销试件合理缺口深度的探讨[J]. 焊接学报, 1981,2(4):10-17.
【11】张君,牛辉. X100管线钢冷裂敏感性研究[J].焊管,2012(11):22-26.
【12】张文钺, 祝美丽, 秦伯雄,等. 焊接冷裂敏感性硬化因子与氢扩散因子的探讨[J]. 兵器材料科学与工程, 1991(12):8-15.
【13】李亚江, 王娟. 焊接缺陷分析与对策[M]. 北京:化学工业出版社, 2014.
【14】徐学利, 张福平, 黄景鹏. X100管线钢焊接冷裂纹敏感性研究[J]. 焊接技术, 2016(8):25-28.
相关信息