Machinability of a New Free-cutting and Non-magnetic Die Steel
摘 要
对YW新型易切削无磁模具钢和对比材料A50钢进行了热处理,并测试了其硬度、相对磁导率,在给定车削条件下进行车削试验,通过测试计算刀具的磨损量来表征钢的切削性能。结果表明:YW 钢经固溶+时效处理后的硬度为42~43 HRC,相对磁导率为1.005~1.019,具有无磁、高硬度的特点;YW 钢由于添加了易切削元素,在相同车削试验条件下,其刀具磨损量比A50钢的减少30%以上。
Abstract
Hardness, relative permeability were tested on a new free-cutting and non-magnetic die steel YW and contractive material steel A50 after heat treatment. The wear loss of the cutting tools used for machining the steel YW and steel A50 was measured at the same cutting conditions so that the machinability of the steels were studied. Results show that the hardness of steel YW after solution and aging treatment was 42-43 HRC. The relative permeability was 1.005-1.019. The steel YW wasnon-magnetical and high hardness. Contractive steel A50, the wear loss of cutting tool machining steel YW was less over 30 percentage than that of cutting tool machining steel A50 based on the addition of free cutting elements.
中图分类号 TG142.45
所属栏目
基金项目 上海市科委应用技术开发专项基金项目(2011-102)
收稿日期
修改稿日期
网络出版日期
作者单位点击查看
引用该论文: XUE Chun,GAO Yushun,HUANG Chunbo,WANG Wenzheng. Machinability of a New Free-cutting and Non-magnetic Die Steel[J]. Materials for mechancial engineering, 2017, 41(Z2): 15~17
薛春,高余顺,黄春波,王文正. 一种新型易切削无磁模具钢的切削性能[J]. 机械工程材料, 2017, 41(Z2): 15~17
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】水恒勇, 刘继雄, 李美琳,等. 热处理工艺对新型节镍奥氏体无磁钢组织和性能的影响[J]. 机械工程材料, 2012, 36(5):69-72.
【2】李志, 高谦, 何冰. 节镍型奥氏体不锈钢1Cr17Mn9Ni4N的组织和力学性能[J]. 钢铁研究学报, 2005, 17(2):68-71.
【3】张桂平. 一种奥氏体无磁不锈切削钢[P]. 中国:1995435. 2007.
【4】张静纬. 易切削钢的新技术和发展方向[J]. 天津冶金, 2003(3):59-61.
【5】李联生, 朱荣, 朱辰,等. 易切削钢中锡的研究[C]//2005年中国钢铁学会论文集.[出版地不详]:[出版者不详],2005.
【6】王小红, 谢兵, 冯仲渝. 国内外易切削钢的现状和研究进展[J]. 特殊钢, 2005, 26(4):26-28.
【2】李志, 高谦, 何冰. 节镍型奥氏体不锈钢1Cr17Mn9Ni4N的组织和力学性能[J]. 钢铁研究学报, 2005, 17(2):68-71.
【3】张桂平. 一种奥氏体无磁不锈切削钢[P]. 中国:1995435. 2007.
【4】张静纬. 易切削钢的新技术和发展方向[J]. 天津冶金, 2003(3):59-61.
【5】李联生, 朱荣, 朱辰,等. 易切削钢中锡的研究[C]//2005年中国钢铁学会论文集.[出版地不详]:[出版者不详],2005.
【6】王小红, 谢兵, 冯仲渝. 国内外易切削钢的现状和研究进展[J]. 特殊钢, 2005, 26(4):26-28.
相关信息