Fracture Toughness of VPTIG Welded Joint of 2219 Al Alloy
摘 要
对2219铝合金变极性钨极惰性气体保护(VPTIG)焊接接头进行了拉伸、冲击和三点弯曲试验,对比研究了接头与母材的拉伸性能、冲击性能、断裂韧性及裂纹扩展行为。结果表明:焊接接头的抗拉强度为266~282 MPa,强度系数为0.6,接头强度远低于母材的;焊缝的冲击功为7~8 J,热影响区的冲击功为6~11 J,均高于母材的;当裂纹扩展量在0.14~0.35 mm时,焊缝裂纹尖端张开位移(CTOD)为0.056~0.124 mm,CTOD随裂纹扩展而增大;焊缝金属表现出比母材更好的断裂韧性,焊缝断口为弹塑性断裂,裂纹扩展区呈韧窝形貌,韧窝内存在第二相质点,使裂纹失稳扩展所消耗的能量增大。
Abstract
The tension, impact and three-point bending tests were conducted on the variable polarity tangent inert gas (VPTIG) welded joint of 2219 Al alloy. Then the tensile property, impact property, fracture toughness and crack propagation process of the joint and base metal were studied and compared. The results show that the tensile strength of the welded joint was between 266 MPa and 282 MPa, which was higher than that of the base metal, and the tensile strength coefficient reached 0.6. The impact energy of the weld and heat affected zone was 7-8 J and 6-11 J, respectively, which were higher than that of the base metal. The crack tip open displacements (CTOD) in the weld were 0.056-0.124 mm with the crack extending of 0.14-0.35 mm. CTOD increased with the extension of cracks. The weld metal exhibited higher fracture toughness than the base metal. The fracture surface of the weld showed an elastic-plastic fracture feature. The crack propagation area showed dimple morphology. Some second phase particles existed in the dimples, resulting in the increase of the unstable propagation energy of the cracks.
中图分类号 TG442 DOI 10.11973/jxgccl201712012
所属栏目 材料性能及应用
基金项目 国防基础科研资助项目(JCKY2014203A001)
收稿日期 2016/10/26
修改稿日期 2017/9/4
网络出版日期
作者单位点击查看
备注田志杰(1975-),男,山东昌乐人,高级工程师,硕士
引用该论文: TIAN Zhijie,XIONG Linyu,LI Ying,DONG Kangying,GAO Hui. Fracture Toughness of VPTIG Welded Joint of 2219 Al Alloy[J]. Materials for mechancial engineering, 2017, 41(12): 54~58
田志杰,熊林玉,李迎,董康英,高辉. 2219铝合金VPTIG焊接接头的断裂韧性[J]. 机械工程材料, 2017, 41(12): 54~58
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】段小雪,田志杰,杜岩峰,等. 2219铝合金搅拌摩擦焊接头的裂纹扩展行为[J].机械工程材料,2014, 38(6):85-88.
【2】张聃,陈文华,孙耀华,等.焊接方法对2219铝合金焊接接头力学性能的影响[J].航空材料学报,2013, 33(1):45-49.
【3】王立民,彭梦都,刘正东,等.热处理工艺对45CrMoV钢组织和冲击韧性的影响[J].材料热处理学报,2015, 36(2):166-170.
【4】覃超,苟国庆,车小莉,等. 合金元素对A7N01S-T5铝合金力学性能和断裂韧性的影响[J].材料研究学报,2015,29(7):535-541.
【5】陈玉喜,刘亮,张华军. 焊接热输入对低合金高强钢焊缝组织和韧性的影响[J].上海交通大学学报,2015, 49(3):306-309.
【6】陈灿龙,李建亮,孔见.6N01铝合金中厚板三点弯曲变形行为的数值模拟[J].机械工程材料,2016, 40(4):59-64.
【7】许良红,田志凌,彭云.微观组织对高强铝合金接头冲击韧度的影响[J].机械工程学报,2009,45(7):108-113.
【8】TAO B H, LI Q, ZHANG Y H. Effects of post-weld heat treatment on fracture toughness of linear friction welded joint for dissimilar titanium alloys[J].Materials Science and Engineering A,2015,634:141-146.
【9】彭业密,黄晖,王燕,等. Al-Mg-Mn-Zr-Er合金冲击韧性研究[J].科学技术与工程,2011, 11(19):4436-4439.
【2】张聃,陈文华,孙耀华,等.焊接方法对2219铝合金焊接接头力学性能的影响[J].航空材料学报,2013, 33(1):45-49.
【3】王立民,彭梦都,刘正东,等.热处理工艺对45CrMoV钢组织和冲击韧性的影响[J].材料热处理学报,2015, 36(2):166-170.
【4】覃超,苟国庆,车小莉,等. 合金元素对A7N01S-T5铝合金力学性能和断裂韧性的影响[J].材料研究学报,2015,29(7):535-541.
【5】陈玉喜,刘亮,张华军. 焊接热输入对低合金高强钢焊缝组织和韧性的影响[J].上海交通大学学报,2015, 49(3):306-309.
【6】陈灿龙,李建亮,孔见.6N01铝合金中厚板三点弯曲变形行为的数值模拟[J].机械工程材料,2016, 40(4):59-64.
【7】许良红,田志凌,彭云.微观组织对高强铝合金接头冲击韧度的影响[J].机械工程学报,2009,45(7):108-113.
【8】TAO B H, LI Q, ZHANG Y H. Effects of post-weld heat treatment on fracture toughness of linear friction welded joint for dissimilar titanium alloys[J].Materials Science and Engineering A,2015,634:141-146.
【9】彭业密,黄晖,王燕,等. Al-Mg-Mn-Zr-Er合金冲击韧性研究[J].科学技术与工程,2011, 11(19):4436-4439.
相关信息