Microstructure and Properties of Sn-Zn-In-Bi-Al Solder Alloy for Sputtering Target Bonding
摘 要
采用微合金化方法制备了Sn-7.0Zn-xIn-3.8Bi-0.2Al (x=0,4.5,5.0,5.5)4种焊料合金,研究了铟含量对焊料合金显微组织、熔点、润湿性、导电性、导热性等的影响,并与传统纯铟、纯锡焊料进行了对比。结果表明:焊料合金主要由β-锡相和富锌相组成;随着铟含量的升高,合金的熔点逐渐降低,润湿性、导电性、导热性逐渐增强;Sn-7.0Zn-5.0In-3.8Bi-0.2Al合金的熔点、润湿性均优于纯锡焊料的,且接近纯铟焊料的,电阻率、热导率均接近纯锡焊料的,该焊料合金为合适的溅射靶材绑定用焊料合金。
Abstract
Four solder alloys of Sn-7.0Zn-xIn-3.8Bi-0.2Al (x=0, 4.5, 5.0, 5.5) were prepared by microalloying method. The influence of the In content on the microstructure, melting point, wettability, electrical conductivity, thermal conductivity of the solder alloys were studied, and compared with the performance of traditional pure In and Sn solders. The results show that the solder alloys consisted essentially of β-Sn and Zn-rich phases. The melting point of the solder alloys gradually decreased and the wettability, electrical conductivity, thermal conductivity increased with the increase of In content.The melting point and wettability of Sn-7.0Zn-5.0In-3.8Bi-0.2Al solder alloy were better than those of pure Sn solder and close to those of of pure In solder. The resistivity and thermal conductivity of the solder alloy were close to those of of pure Sn solder.It was confirmed that Sn-7.0Zn-5.0In-3.8Bi-0.2Al solder alloy was suitable for sputtering target bonding.
中图分类号 TG425 DOI 10.11973/jxgccl201801013
所属栏目 材料性能及应用
基金项目
收稿日期 2016/10/28
修改稿日期 2017/10/11
网络出版日期
作者单位点击查看
备注燕翙江(1990-),女,河北石家庄人,硕士研究生
引用该论文: YAN Huijiang,ZHANG Jianxin,BU Lijing,ZHU Chaogang,YANG Yong,CHU Zhenhua,DONG Yanchun,HE Jining,LIU Na. Microstructure and Properties of Sn-Zn-In-Bi-Al Solder Alloy for Sputtering Target Bonding[J]. Materials for mechancial engineering, 2018, 42(1): 64~67
燕翙江,张建新,卜丽静,朱朝刚,杨勇,褚振华,董艳春,何继宁,刘娜. 溅射靶材绑定用Sn-Zn-In-Bi-Al焊料合金的组织与性能[J]. 机械工程材料, 2018, 42(1): 64~67
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】梁静,林小辉. 等离子喷涂技术在溅射靶材制备中的应用[J]. 中国钼业,2014,38(2):43-46.
【2】段国晨,齐暑华,吴新明.微电子封装用导电胶的研究进展[J].中国胶粘剂,2010,19(2):54-60.
【3】薛伟峰,刘炳龙.微波芯片元件的导电胶粘接工艺与应用[J].电子工艺技术,2012,33(3):156-159.
【4】LIN C M. Influence of thermal storage on microstructure and properties of Sn-9Zn-xIn alloys[J]. Canadian Metallurgical Quarterly, 2013, 52(1):98-105.
【5】SUN L, ZHANG L. The wettability and oxidation resistance of Sn-Zn-X lead-free solder joints[J]. Aer-Advances In Engineering Research, 2015, 20:188-190.
【6】吴晓婧,薛烽,周健,等. Cu, Ni对Sn-Zn-Al无铅焊料组织和性能的影响[J]. 东南大学学报:自然科学版,2009,39(3):623-628.
【7】SPINELLI J E, SILVA B L, GARCIA A. Microstructure, phases morphologies and hardness of a Bi-Ag eutectic alloy for high temperature soldering applications[J]. Materials & Design, 2014, 58:482-490.
【8】HUANG M L, HOU X L, KANG N, et al. Microstructure and interfacial reaction of Sn-Zn-x(Al, Ag) near-eutectic solders on Al and Cu substrates[J].Journal of Materials Science-materials in Electronics, 2014, 25(5):2311-2319.
【9】吕娟,赵麦群,王秀春,等.微量Re和Al对Sn-9Zn焊料组织与性能的影响[J].电子元件与材料, 2009, 28(8):39-42.
【10】董明杰. Sn-Bi-In-Zn-Ag系合金组织及连接界面[D].天津:天津大学,2011.
【11】周健,孙扬善,薛烽.电子产品用无铅焊料的研究现状和趋势[J].机械工程材料,2005, 29(3):11-14.
【12】袁宜耀, 孙勇, 吴敏. 无铅Sn-Ag-Sb与Sn-Zn-In润湿性研究[J]. 电子工艺技术,2006,28(3):135-138.
【2】段国晨,齐暑华,吴新明.微电子封装用导电胶的研究进展[J].中国胶粘剂,2010,19(2):54-60.
【3】薛伟峰,刘炳龙.微波芯片元件的导电胶粘接工艺与应用[J].电子工艺技术,2012,33(3):156-159.
【4】LIN C M. Influence of thermal storage on microstructure and properties of Sn-9Zn-xIn alloys[J]. Canadian Metallurgical Quarterly, 2013, 52(1):98-105.
【5】SUN L, ZHANG L. The wettability and oxidation resistance of Sn-Zn-X lead-free solder joints[J]. Aer-Advances In Engineering Research, 2015, 20:188-190.
【6】吴晓婧,薛烽,周健,等. Cu, Ni对Sn-Zn-Al无铅焊料组织和性能的影响[J]. 东南大学学报:自然科学版,2009,39(3):623-628.
【7】SPINELLI J E, SILVA B L, GARCIA A. Microstructure, phases morphologies and hardness of a Bi-Ag eutectic alloy for high temperature soldering applications[J]. Materials & Design, 2014, 58:482-490.
【8】HUANG M L, HOU X L, KANG N, et al. Microstructure and interfacial reaction of Sn-Zn-x(Al, Ag) near-eutectic solders on Al and Cu substrates[J].Journal of Materials Science-materials in Electronics, 2014, 25(5):2311-2319.
【9】吕娟,赵麦群,王秀春,等.微量Re和Al对Sn-9Zn焊料组织与性能的影响[J].电子元件与材料, 2009, 28(8):39-42.
【10】董明杰. Sn-Bi-In-Zn-Ag系合金组织及连接界面[D].天津:天津大学,2011.
【11】周健,孙扬善,薛烽.电子产品用无铅焊料的研究现状和趋势[J].机械工程材料,2005, 29(3):11-14.
【12】袁宜耀, 孙勇, 吴敏. 无铅Sn-Ag-Sb与Sn-Zn-In润湿性研究[J]. 电子工艺技术,2006,28(3):135-138.
相关信息