Cause Analysis on Fracture of Tubing Joint in an Oil Well
摘 要
某油井生产11个月后发生油管短节断裂失效事故。通过对失效油管短节的宏观和微观形貌观察、显微组织分析、力学性能测试、化学成分分析,查明了其断裂失效原因。结果表明:该油管短节断裂主要是由于在油井生产工况下,油管内壁发生了多裂纹源的应力腐蚀开裂,然后在腐蚀和机械载荷的共同作用下,裂纹不断扩展并相互连接,当裂纹穿透管壁后表现为腐蚀疲劳开裂,最终导致油管短节断裂失效;油管短节加工工艺不当,提高了其断裂失效的概率。
Abstract
Fracture failure of a tubing joint occurred in an oil well after production for 11 months. Through the macroscopic and microscopic morphology observation, microstructure analysis, mechanical property test and chemical composition analysis to the fractured tubing joint, the fracture reasons were found out. The results show that the fracture of the tubing joint was mainly caused by multi cracks stress corrosion cracking on the inner wall of the tubing joint under the production conditions of the oil well. Then under the interaction of corrosion and mechanical loads, the cracks continuously extended and connected with each other, and when the cracks penetrated the wall thickness of the tubing joint, they showed corrosion fatigue cracking, which eventually led to the fracture failure of the tubing joint. Improper processing technology of the tubing joint increased the probability of fracture failure.
中图分类号 TE983 TG157 DOI 10.11973/lhjy-wl201806015
所属栏目 质量控制与失效分析
基金项目
收稿日期 2017/7/25
修改稿日期
网络出版日期
作者单位点击查看
备注张辉(1980-),男,工程师,主要从事海洋石油钻完井技术工作,343901251@qq.com
引用该论文: ZHANG Hui. Cause Analysis on Fracture of Tubing Joint in an Oil Well[J]. Physical Testing and Chemical Analysis part A:Physical Testing, 2018, 54(6): 457~462
张辉. 某油井油管短节断裂原因分析[J]. 理化检验-物理分册, 2018, 54(6): 457~462
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】高进,孙金. 金属材料应力腐蚀失效分析[J]. 山东轻工业学院学报(自然科学版),2001,15(1):47-50.
【2】王双来,杜志杰,彭娜. 某井油管变扣短节断裂原因分析[J]. 理化检验(物理分册),2015,51(10):730-732.
【3】张亚明,臧晗宇,董爱华,等. 13Cr钢油管腐蚀原因分析[J]. 腐蚀科学与防护技术,2009,21(5):499-501.
【4】张威,王铎. 高温高压CO2含Cl-环境下超级Cr13马氏体不锈钢的腐蚀行为[J]. 兵器材料科学与工程,2014,37(1):111-114.
【5】张清廉,李铭,王起江. 20G无缝钢管穿孔泄漏失效分析[J]. 理化检验(物理分册),2016,52(4):265-269.
【6】解挺,尹延国,朱元. 马氏体不锈钢的热处理和性能[J]. 国外金属热处理,1996(6):38-40.
【7】陈亚伟. 论应力腐蚀断裂[J]. 中国化工装备,2001,3(2):43-49.
【8】朱向群,戴起勋,周明,等. 回火温度对2Cr13不锈钢应力腐蚀开裂和力学滞后的影响[J]. 材料热处理学报,2009,30(1):11-14,19.
【9】崔璐,李臻,王建才,等. 油井管的腐蚀疲劳研究进展[J]. 石油机械,2015,43(1):78-83.
【2】王双来,杜志杰,彭娜. 某井油管变扣短节断裂原因分析[J]. 理化检验(物理分册),2015,51(10):730-732.
【3】张亚明,臧晗宇,董爱华,等. 13Cr钢油管腐蚀原因分析[J]. 腐蚀科学与防护技术,2009,21(5):499-501.
【4】张威,王铎. 高温高压CO2含Cl-环境下超级Cr13马氏体不锈钢的腐蚀行为[J]. 兵器材料科学与工程,2014,37(1):111-114.
【5】张清廉,李铭,王起江. 20G无缝钢管穿孔泄漏失效分析[J]. 理化检验(物理分册),2016,52(4):265-269.
【6】解挺,尹延国,朱元. 马氏体不锈钢的热处理和性能[J]. 国外金属热处理,1996(6):38-40.
【7】陈亚伟. 论应力腐蚀断裂[J]. 中国化工装备,2001,3(2):43-49.
【8】朱向群,戴起勋,周明,等. 回火温度对2Cr13不锈钢应力腐蚀开裂和力学滞后的影响[J]. 材料热处理学报,2009,30(1):11-14,19.
【9】崔璐,李臻,王建才,等. 油井管的腐蚀疲劳研究进展[J]. 石油机械,2015,43(1):78-83.
相关信息