Flow Stress Constitutive Equation of 2219 Aluminum Alloy During Hot Compression
摘 要
采用Gleeble-3180型热模拟试验机对2219铝合金进行单道次热压缩试验,研究了该铝合金在温度为200~350℃、应变速率为0.1~10.0 s-1条件下的流变行为,建立了2219铝合金热压缩时的流变应力本构方程,并进行了试验验证。结果表明:2219铝合金的流变应力随应变速率的增大或变形温度的降低而增加;由Fields-Backofen本构方程计算得到的2219铝合金应力的变化规律与试验得到的相同,且应力计算值与试验值的相对误差小于5%,该本构方程可以较准确地描述2219铝合金的高温流变行为。
Abstract
The flow behavior of 2219 aluminium alloy was studied by single pass hot compression at the temperatures of 200-350℃ and strain rates of 0.1-10.0 s-1 with Gleeble-3180 thermal mechanical simulator. The flow stress constitutive equation of 2219 aluminum alloy during hot compression was established and verified by experiments. The results show that the flow stress of 2219 aluminum alloy increased with the increase of strain rate or the decrease of deformation temperature. The change rule of stress calculated by Fields-Backofen constitutive equation was the same with that by experiments, and the relative error between calculated and tested stresses was less than 5%. The constitutive equation described the high temperature flow behavior of 2219 aluminium alloy accurately.
中图分类号 TG306 DOI 10.11973/jxgccl201807011
所属栏目 物理模拟与数值模拟
基金项目 国家重点基础研究发展计划(973计划)项目(2014CB046600)
收稿日期 2017/7/18
修改稿日期 2018/5/25
网络出版日期
作者单位点击查看
备注易兆祥(1993-),男,湖南株洲人,硕士研究生
引用该论文: YI Zhaoxiang,LI Xinhe,CHANG Shiwu,CAO Quan. Flow Stress Constitutive Equation of 2219 Aluminum Alloy During Hot Compression[J]. Materials for mechancial engineering, 2018, 42(7): 53~56
易兆祥,李新和,常士武,曹权. 2219铝合金热压缩时的流变应力本构方程[J]. 机械工程材料, 2018, 42(7): 53~56
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】刘燕.贮箱用2219铝合金热处理工艺研究[D].天津:天津大学,2013.
【2】张涛.旋压成形工艺[M].北京:化学工业出版社,2009.
【3】张华,孙大同,张贺,等.2219铝合金搅拌摩擦焊接接头剥落腐蚀机理[J].稀有金属材料与工程,2015,44(1):103-107.
【4】贺永海,张立武,胡春炜,等.2219铝合金搅拌摩擦焊工艺及接头性能[J].机械工程材料,2008,32(2):37-39.
【5】金醇,黄亮,李建军,等.不同热处理状态下成形速率对2219铝合金成形极限的影响[J].塑性工程学报,2017,24(1):125-132.
【6】尹旭妮,湛利华,赵俊.2219铝合金稳态蠕变本构方程的建立[J].中国有色金属学报,2014(9):2250-2256.
【2】张涛.旋压成形工艺[M].北京:化学工业出版社,2009.
【3】张华,孙大同,张贺,等.2219铝合金搅拌摩擦焊接接头剥落腐蚀机理[J].稀有金属材料与工程,2015,44(1):103-107.
【4】贺永海,张立武,胡春炜,等.2219铝合金搅拌摩擦焊工艺及接头性能[J].机械工程材料,2008,32(2):37-39.
【5】金醇,黄亮,李建军,等.不同热处理状态下成形速率对2219铝合金成形极限的影响[J].塑性工程学报,2017,24(1):125-132.
【6】尹旭妮,湛利华,赵俊.2219铝合金稳态蠕变本构方程的建立[J].中国有色金属学报,2014(9):2250-2256.
相关信息