Evaluation on Measurement Uncertainty of Tensile Test of Metallic Materials at Room Temperature
摘 要
对金属材料室温拉伸试验的测量不确定度的来源进行了分析,通过建立数学模型和重复性试验评定了金属材料室温拉伸试验的测量不确定度。结果表明:作为规范化的检测试验室,在人员、机器、原料、方法、环境和管理等受控以及包含因子k=2的条件下,下屈服强度的相对扩展不确定度Urel(ReL)=2.9%,抗拉强度的相对扩展不确定度Urel(Rm)=1.6%,断后伸长率的相对扩展不确定度Urel(A)=2.8%,断面收缩率的相对扩展不确定度Urel(Z)=2.1%;本文采用的评定方法可为金属材料室温拉伸试验测量不确定度的评定提供一定参考。
Abstract
The source of the uncertainty of measurement in metallic materials at room temperature tensile test was analyzed, and the uncertainty of measurement of the metallic materials at the room temperature tensile test was evaluated by establishing mathematical model and repeatability test. The results show that as a standardized testing laboratory, under the controlled conditions of man, machine, material, method, environment and management, and under the condition of containing factor k=2, relative expansion uncertainty of lower yield strength Urel (ReL)=2.9%, relative expansion uncertainty of tensile strength Urel(Rm)=1.6%, relative expansion uncertainty of elongation after fracture Urel(A)=2.8%, relative expansion uncertainty of section shrinkage rate Urel(Z)=2.1%. The evaluation method adopted in this paper provides reference for the evaluation of uncertainty in measurement of metallic materials at room temperature tensile test.
中图分类号 TG115 DOI 10.11973/lhjy-wl201809009
所属栏目 专题报道(拉伸试验)
基金项目
收稿日期 2018/4/28
修改稿日期
网络出版日期
作者单位点击查看
备注赵永锋(1978-),男,工程师,主要从事金相分析和物理检测技术工作,zyflwy@163.com
引用该论文: ZHAO Yongfeng,LIN Xiaogang,CHEN Jie,TANG Zhigang. Evaluation on Measurement Uncertainty of Tensile Test of Metallic Materials at Room Temperature[J]. Physical Testing and Chemical Analysis part A:Physical Testing, 2018, 54(9): 657~661
赵永锋,林小刚,陈杰,唐志刚. 金属材料室温拉伸试验测量不确定度的评定[J]. 理化检验-物理分册, 2018, 54(9): 657~661
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】王承忠. 材料理化检验测量不确定度评定方法的研究[J]. 理化检验(物理分册),2007,43(6):282-286.
【2】王承忠. 材料理化检验测量不确定度评估指南及实例:CNAS-GL10:2006[M]. 北京:中国计量出版社,2007.
【3】王承忠. 测量不确定度基本原理和评定方法及在材料检测中的评定实例第六讲测量不确定度的评定方法(测量不确定度的评定方法及步骤)[J]. 理化检验(物理分册),2014,50(1):823-826.
【4】王承忠. 测量不确定度原理及在理化检验中的应用第七讲不确定度与误差的区别及在评定中应注意的几个问题[J]. 理化检验(物理分册),2003,39(7):382-386.
【2】王承忠. 材料理化检验测量不确定度评估指南及实例:CNAS-GL10:2006[M]. 北京:中国计量出版社,2007.
【3】王承忠. 测量不确定度基本原理和评定方法及在材料检测中的评定实例第六讲测量不确定度的评定方法(测量不确定度的评定方法及步骤)[J]. 理化检验(物理分册),2014,50(1):823-826.
【4】王承忠. 测量不确定度原理及在理化检验中的应用第七讲不确定度与误差的区别及在评定中应注意的几个问题[J]. 理化检验(物理分册),2003,39(7):382-386.
相关信息