Cause of Fracture on Special Equipment Wire Rope
摘 要
采用宏观检验、断口分析、显微组织观察、化学成分分析、拆股试验等方法对特种设备用钢丝绳的断裂原因进行分析。结果表明:钢丝绳发生了疲劳断裂。在使用过程中钢丝绳承受着拉、弯、扭、挤、振动等复杂交变应力,使得钢丝绳外层股以及绳芯钢丝局部应力集中,同时在挤压、摩擦过程中温度升高导致表面组织发生相变,进而产生微裂纹,裂纹扩展导致断裂。绳芯钢丝比外层股钢丝磨损得更快,首先失效;在绳芯失效后,外层股钢丝磨损加速,进而导致钢丝绳整体失效。
Abstract
Broken cause of wire rope for special equipment was analyzed by macroscopic inspection, fracture analysis, microstructure observation, chemical composition analysis, dismantling test, and so on. The results show that the wire rope failed by fatigue fracture. During use, the wire rope was subjected to complex alternating stresses such as tension, bending, torsion, extrusion and vibration, leading to local stress concentration of the outer strand wires and core wires of the rope; meanwhile, the rising temperature during the extrusion and friction process led to the surface phase transition. Therefore microcracks were initiated and propagated, resulting in the fracture. The core wires wore faster than the outer strand wires, and first failed. After the failure of the rope core, the outer strand wires wore up quickly, resulting in the overall failure of the wire rope.
中图分类号 TG111.91 DOI 10.11973/jxgccl201908013
所属栏目 残余应力
基金项目
收稿日期 2018/8/8
修改稿日期 2019/7/15
网络出版日期
作者单位点击查看
备注桂旭(1980-),男,江苏南通人,高级工程师,硕士
引用该论文: GUI Xu,YANG Jinyan. Cause of Fracture on Special Equipment Wire Rope[J]. Materials for mechancial engineering, 2019, 43(8): 64~68
桂旭,杨金艳. 特种设备用钢丝绳断裂的原因[J]. 机械工程材料, 2019, 43(8): 64~68
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】巴发海, 薛宇. 起重机钢丝绳断裂失效分析[J]. 机械工程材料, 2016, 40(8):103-106.
【2】李娟, 吴剑勇, 田华, 等.港口门机用钢丝绳断裂原因分析[C]//2015年全国失效分析学术会议论文集.北京:中国机械工程学会, 2015:29-33.
【3】崔影, 刘艳, 刘震, 等. 电梯曳引钢丝绳强度级别讨论[J]. 金属制品, 2010, 36(6):70-72.
【4】肖永清. 起重钢丝绳的失效分析与安全使用[J]. 金属制品, 2010, 36(6):63-67.
【5】崔影. 钢丝绳设计基本原则[J]. 金属制品, 2018, 44(3):17-20.
【2】李娟, 吴剑勇, 田华, 等.港口门机用钢丝绳断裂原因分析[C]//2015年全国失效分析学术会议论文集.北京:中国机械工程学会, 2015:29-33.
【3】崔影, 刘艳, 刘震, 等. 电梯曳引钢丝绳强度级别讨论[J]. 金属制品, 2010, 36(6):70-72.
【4】肖永清. 起重钢丝绳的失效分析与安全使用[J]. 金属制品, 2010, 36(6):63-67.
【5】崔影. 钢丝绳设计基本原则[J]. 金属制品, 2018, 44(3):17-20.
相关信息