A Detection Method of Rolled Thread Streamline of Inconel 718 Alloy Bolts
摘 要
Inconel 718合金螺栓为航空发动机中常用的高强度螺栓,通常采用滚压螺纹成型工艺。螺栓及螺纹的流线直接影响螺栓的质量和服役寿命,所以流线检测尤为重要。通过试验,发现将Inconel 718合金螺栓进行二次固溶+时效处理可使其晶粒长大和析出δ相(Ni3Nb),然后在HNO3+HF的溶液中浸蚀1 h,可以清晰显示出Inconel 718合金螺栓和螺纹的流线。
Abstract
Inconel 718 alloy bolts are a high strength bolts commonly used in the aeroengine, and they usually adopt rolled thread technology. The streamline of bolts and threads directly affects the quality and service life of the bolts, so streamline detection is particularly important. Through test, it is found that grain growth and δ phase (Ni3Nb) precipitation can be achieved by secondary solution and aging treatment of Inconel 718 alloy bolts. And then the streamline of Inconel 718 alloy bolts and threads can be clearly displayed by etching in HNO3+HF solution for 1 h.
中图分类号 TG115.9 DOI 10.11973/lhjy-wl201909008
所属栏目 试验技术与方法
基金项目
收稿日期 2018/9/14
修改稿日期
网络出版日期
作者单位点击查看
备注张俊(1991-),男,硕士,主要从事理化检验和材料研究工作,13568828354@163.com
引用该论文: ZHANG Jun,LIU Weidong,GONG Xiaoning. A Detection Method of Rolled Thread Streamline of Inconel 718 Alloy Bolts[J]. Physical Testing and Chemical Analysis part A:Physical Testing, 2019, 55(9): 626~629
张俊,刘卫东,龚晓宁. Inconel 718合金螺栓滚压螺纹流线的检测方法[J]. 理化检验-物理分册, 2019, 55(9): 626~629
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】THOMAS A,EL-WAHABI M,CABRERA J M,et al. High temperature deformation of Inconel 718[J]. Journal of Materials Processing Technology,2006,177(3):469-472.
【2】RAHMAN M,SEAH W K,TEO T T. The machinability of Inconel 718[J]. Journal of Materials Processing Technology,1997,63(1):199-204.
【3】齐欢. INCONEL 718(GH4169)高温合金的发展与工艺[J]. 材料工程,2012(8):92-100.
【4】《中国航空材料手册》委员会. 中国航空材料手册(第2卷)[M]. 北京:中国标准出版社,2002.
【5】王玉凤,刘风雷,庄宝潼. Inconel 718十二角头螺栓制造工艺技术研究[J]. 航空制造技术,2015,479(10):79-82.
【6】张腾,李鹏远,许丹,等. ITER 718合金螺栓断裂原因分析及工艺改进[J]. 核聚变与等离子体物理,2015(2):120-124.
【7】奚爱军. 螺纹滚压加工工艺研究[J]. 现代车用动力,2015(2):48-52.
【8】史艳霞. 一种高强度螺栓零件加工工艺研究[D]. 大连:大连理工大学,2016.
【9】张玉勋,易幼平,李云,等. 铝合金机轮轮毂锻造流线仿真与实验研究[J]. 中南大学学报(自然科学版),2011,42(7):1967-1972.
【10】CLEGG R. Case studies in engineering failure analysis[J]. Case Studies in Engineering Failure Analysis,2013,1(1):4-5.
【11】姜涛,刘含洋,刘杰,等. 30CrMnSiA钢制吊耳断裂原因分析[J]. 金属热处理,2011(增刊1):49-53.
【12】权仁泽,鹿云,潘艳春. 增压柴油发动机排气门盘部断裂分析[J]. 金属热处理,2002,27(2):46-47.
【2】RAHMAN M,SEAH W K,TEO T T. The machinability of Inconel 718[J]. Journal of Materials Processing Technology,1997,63(1):199-204.
【3】齐欢. INCONEL 718(GH4169)高温合金的发展与工艺[J]. 材料工程,2012(8):92-100.
【4】《中国航空材料手册》委员会. 中国航空材料手册(第2卷)[M]. 北京:中国标准出版社,2002.
【5】王玉凤,刘风雷,庄宝潼. Inconel 718十二角头螺栓制造工艺技术研究[J]. 航空制造技术,2015,479(10):79-82.
【6】张腾,李鹏远,许丹,等. ITER 718合金螺栓断裂原因分析及工艺改进[J]. 核聚变与等离子体物理,2015(2):120-124.
【7】奚爱军. 螺纹滚压加工工艺研究[J]. 现代车用动力,2015(2):48-52.
【8】史艳霞. 一种高强度螺栓零件加工工艺研究[D]. 大连:大连理工大学,2016.
【9】张玉勋,易幼平,李云,等. 铝合金机轮轮毂锻造流线仿真与实验研究[J]. 中南大学学报(自然科学版),2011,42(7):1967-1972.
【10】CLEGG R. Case studies in engineering failure analysis[J]. Case Studies in Engineering Failure Analysis,2013,1(1):4-5.
【11】姜涛,刘含洋,刘杰,等. 30CrMnSiA钢制吊耳断裂原因分析[J]. 金属热处理,2011(增刊1):49-53.
【12】权仁泽,鹿云,潘艳春. 增压柴油发动机排气门盘部断裂分析[J]. 金属热处理,2002,27(2):46-47.
相关信息