Cause Analysis on Fracture of Cylinder Piston Rod
摘 要
某工程机械油缸活塞杆在使用初期即发生一次性脆性断裂,通过宏观分析、化学成分分析、硬度测试、断口分析及金相检验对活塞杆断裂失效的原因进行了分析。结果表明:热处理工艺不当使该活塞杆中出现网状铁素体和魏氏组织,引起了晶界脆化,加之试样中硫化物类夹杂含量较高,导致活塞杆承受交变载荷的能力下降,最终发生脆性断裂。
Abstract
Brittle fracture of the piston rod of construction machinery cylinder occurred in the early use. Through macroscopic analysis, chemical composition analysis, hardness test, fracture analysis and metallographic examination, the fracture causes of piston rod were analyzed. The results show that ferrite net and widmanstatten structure appeared in the piston rod due to improper heat treatment, which caused grain boundary embrittlement, and there were too much sulfides inclusions in the material. As a result, the ability of piston rod to bear alternating loads decreased and brittle fracture finally occurred.
中图分类号 TH142.1 DOI 10.11973/lhjy-wl201910014
所属栏目 质量控制与失效分析
基金项目
收稿日期 2019/5/7
修改稿日期
网络出版日期
作者单位点击查看
备注甘美露(1978-),男,工程师,硕士,主要从事材料疲劳和腐蚀方面的分析检验工作,ganml2002@163.com
引用该论文: GAN Meilu,ZHANG Qiang,WANG Shuqiang,XIE Jianping,SHEN Rui,LEI Qinglin. Cause Analysis on Fracture of Cylinder Piston Rod[J]. Physical Testing and Chemical Analysis part A:Physical Testing, 2019, 55(10): 733~736
甘美露,张强,王书强,谢建平,沈睿,雷青林. 油缸活塞杆断裂原因分析[J]. 理化检验-物理分册, 2019, 55(10): 733~736
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】李毅,朱鹏霄,陈波. 油缸活塞杆断裂失效分析[J]. 理化检验(物理分册),2015,51(11):824-826.
【2】HULL D. Fractography:Observing, Measuring and Interpreting Fracture Surface Topography[M]. Cambridge:Cambridge University Press,1999.
【3】周仲荣,LEO V. 微动磨损[M]. 北京:科学出版社,2002.
【4】吴佳峻. 18CrNiMo7-6钢齿轮轴开裂失效分析[J]. 理化检验(物理分册),2017,53(9):671-674.
【5】胡伟勇,王峰,张泽南,等. 3Cr2W8V合金钢轴承套圈用热挤压心棒断裂失效分析[J]. 理化检验(物理分册),2018,54(7):523-525.
【6】马永恒. 减震器活塞杆断裂失效分析[J]. 理化检验(物理分册),2013,49(增刊2):361-363.
【7】杨星红,王荣. 电梯驱动轴断裂原因分析[J]. 理化检验(物理分册),2014,50(4):292-295.
【8】上海市机械制造工艺研究所. 金相分析技术[M]. 上海:上海科学技术文献出版社,1987.
【2】HULL D. Fractography:Observing, Measuring and Interpreting Fracture Surface Topography[M]. Cambridge:Cambridge University Press,1999.
【3】周仲荣,LEO V. 微动磨损[M]. 北京:科学出版社,2002.
【4】吴佳峻. 18CrNiMo7-6钢齿轮轴开裂失效分析[J]. 理化检验(物理分册),2017,53(9):671-674.
【5】胡伟勇,王峰,张泽南,等. 3Cr2W8V合金钢轴承套圈用热挤压心棒断裂失效分析[J]. 理化检验(物理分册),2018,54(7):523-525.
【6】马永恒. 减震器活塞杆断裂失效分析[J]. 理化检验(物理分册),2013,49(增刊2):361-363.
【7】杨星红,王荣. 电梯驱动轴断裂原因分析[J]. 理化检验(物理分册),2014,50(4):292-295.
【8】上海市机械制造工艺研究所. 金相分析技术[M]. 上海:上海科学技术文献出版社,1987.
相关信息