Effect of Heat Treatment on Corrosion Resistance of 3D Printed Titanium Alloy
摘 要
采用电化学方法研究了不同热处理条件(沉积态,时效态,时效水冷态)下3D打印钛合金在1 mol/L盐酸溶液中的耐蚀性,同时观察了合金的显微组织。结果表明:3D打印钛合金为细小的针状α+β网篮组织;时效处理后,α相析出且粗化,耐蚀性减弱;水冷处理后,组织转变为特殊的α+β网篮组织,由粗大的片层α相和细小针状α相组成,耐蚀性进一步减弱。在1 mol/L盐酸溶液中,沉积态合金的耐蚀性最强,时效态合金的耐蚀性次之,时效水冷态合金的耐蚀性最差。
Abstract
Electrochemical method was used to study the corrosion resistance of 3D printed titanium alloy in 1 mol/L hydrochloric acid solution under different heat treatment conditions, and the microstructure of the alloy was also observed. The results show that the structure of the 3D printed titanium alloy was a fine needle-like α + β net basket structure; after aging treatment, α phase precipitated and coarsened, and the corrosion resistance was weakened; after water cooling treatment, the structure of the alloy was transformed into a special α + β net structure,which was composed of coarse lamellar α phase and fine needle-shaped α phase, and the corrosion resistance was further weakened. In the 1 mol/L hydrochloric acid solution, the corrosion resistance of as-deposited alloy was the strongest, the corrosion resistance of ageing alloy was the second, and the corrosion resistance of ageing water-cooled alloy was the worst.
中图分类号 TG174 DOI 10.11973/fsyfh-202005006
所属栏目 试验研究
基金项目
收稿日期 2019/4/23
修改稿日期
网络出版日期
作者单位点击查看
引用该论文: SHANG Jin,CAO Wei,CHEN Yongchang. Effect of Heat Treatment on Corrosion Resistance of 3D Printed Titanium Alloy[J]. Corrosion & Protection, 2020, 41(5): 27
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】徐增华. 金属耐蚀材料第十二讲钛合金[J]. 腐蚀与防护,2002,23(1):42-45.
【2】杨专钊,刘道新,张晓化. 钛及钛合金的缝隙腐蚀行为[J]. 腐蚀与防护,2013,34(4):295-297.
【3】张玮航,周文博,潘红娟. 不同打印参数对3D打印钛合金电化学腐蚀的影响[J]. 广东化工,2017,44(1):35-36.
【4】ALAGIC I,CVIJOVIC Z,MITROVIC S,et al. Wear and corrosion behaviour of Ti-13Nb-13Zr and Ti-6Al-4V alloys in simulated physiological solution[J]. Corrosion Science,2011,53(2):796-808.
【5】何博文,冉先喆,田象军,等. 激光增材制造TC11钛合金的耐蚀性研究[J]. 中国激光,2016,43(4):81-87.
【6】姜应律,吴荫顺. 用极化曲线研究钛合金在水、醇中腐蚀机理的差异[J]. 腐蚀科学与防护技术,2005,17(3):154-158.
【7】朱玉琴,苏艳,舒畅,等. TC18钛合金在海洋大气环境中的腐蚀行为研究[J]. 装备环境工程,2018,15(3):35-38.
【8】李小宇,郑美华,王洁琪,等. 3D打印和铸造钴铬合金耐蚀性及力学稳定性比较[J]. 中华口腔医学研究杂志(电子版),2016,10(5):327-332.
【9】卓君. 热处理对3D打印TC4钛合金组织与力学性能的影响[J]. 钛工业进展,2019,36(4):19-23.
【10】曹楚南. 腐蚀电化学[J]. 自然杂志,1983,5(4):266-270.
【11】王海杰,王佳,彭欣,等. 钛合金在3.5% NaCl溶液中的腐蚀行为[J]. 中国腐蚀与防护学报,2015,35(1):75-80.
【2】杨专钊,刘道新,张晓化. 钛及钛合金的缝隙腐蚀行为[J]. 腐蚀与防护,2013,34(4):295-297.
【3】张玮航,周文博,潘红娟. 不同打印参数对3D打印钛合金电化学腐蚀的影响[J]. 广东化工,2017,44(1):35-36.
【4】ALAGIC I,CVIJOVIC Z,MITROVIC S,et al. Wear and corrosion behaviour of Ti-13Nb-13Zr and Ti-6Al-4V alloys in simulated physiological solution[J]. Corrosion Science,2011,53(2):796-808.
【5】何博文,冉先喆,田象军,等. 激光增材制造TC11钛合金的耐蚀性研究[J]. 中国激光,2016,43(4):81-87.
【6】姜应律,吴荫顺. 用极化曲线研究钛合金在水、醇中腐蚀机理的差异[J]. 腐蚀科学与防护技术,2005,17(3):154-158.
【7】朱玉琴,苏艳,舒畅,等. TC18钛合金在海洋大气环境中的腐蚀行为研究[J]. 装备环境工程,2018,15(3):35-38.
【8】李小宇,郑美华,王洁琪,等. 3D打印和铸造钴铬合金耐蚀性及力学稳定性比较[J]. 中华口腔医学研究杂志(电子版),2016,10(5):327-332.
【9】卓君. 热处理对3D打印TC4钛合金组织与力学性能的影响[J]. 钛工业进展,2019,36(4):19-23.
【10】曹楚南. 腐蚀电化学[J]. 自然杂志,1983,5(4):266-270.
【11】王海杰,王佳,彭欣,等. 钛合金在3.5% NaCl溶液中的腐蚀行为[J]. 中国腐蚀与防护学报,2015,35(1):75-80.
相关信息