Cause Analysis on Fracture of Fastening Stud of Diesel Engine in a Nuclear Power Unit
摘 要
某核电机组柴油机紧固螺柱在回装过程中发生断裂。采用宏观观察、化学成分分析、金相检验、硬度测试、扫描电镜分析和能谱分析等方法对螺柱断裂原因进行了分析。结果表明:由于螺柱材料淬火温度控制不正确、淬火冷速不合适,导致螺柱中形成了淬火裂纹,在回装过程中的安装扭矩作用下,螺柱在淬火裂纹处发生一次性过载断裂。
Abstract
The fastening stud of diesel engine in a nuclear power unit broke during reassembly. The causes of stud fracture were analyzed by means of macroscopic observation, chemical composition analysis, metallographic examination, hardness test, scanning electron microscope analysis and energy disperse spectroscopy analysis. The results show that the quenching crack was formed in stud due to the improper quenching temperature control and the improper quenching speed. Under the action of the installation torque in the process of reassembly, one-time overload fracture occured at the quenching crack of stud.
中图分类号 TG115.2 DOI 10.11973/lhjy-wl202005011
所属栏目 质量控制与失效分析
基金项目
收稿日期 2020/1/20
修改稿日期
网络出版日期
作者单位点击查看
备注张玉忠(1980-),男,高级工程师,从事核电站金属监督及管理工作,zhangyuzhong@cgnpc.com.cn
引用该论文: ZHANG Yuzhong,YANG Zheyi,SHI Zhigang,ZHANG Baozhu. Cause Analysis on Fracture of Fastening Stud of Diesel Engine in a Nuclear Power Unit[J]. Physical Testing and Chemical Analysis part A:Physical Testing, 2020, 56(5): 43~47
张玉忠,杨哲一,史志刚,张宝柱. 某核电机组柴油机紧固螺柱断裂原因分析[J]. 理化检验-物理分册, 2020, 56(5): 43~47
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】潘伟,史志刚,朱珊珊,等. 柴油发电机固定螺钉断裂失效分析[J]. 理化检验(物理分册),2019,55(3):209-213.
【2】黄嘉乐,钱锟,韩波. 10. 9级高强螺栓头部断裂原因分析[J]. 理化检验(物理分册),2019,55(10):718-721.
【3】腾巍,梁博,孙晓庭,等. 42CrMo钢高强度螺栓轴向开裂失效分析[J]. 理化检验(物理分册),2017,53(4):296-298.
【4】张栋,钟培德,陶春虎,等. 失效分析[M]. 北京:国防工业出版社,2004.
【5】钟群鹏,赵子华. 断口学[M]. 北京:高等教育出版社,2006.
【6】钟群鹏,周煜,张峥. 裂纹学[M]. 北京:高等教育出版社,2014.
【2】黄嘉乐,钱锟,韩波. 10. 9级高强螺栓头部断裂原因分析[J]. 理化检验(物理分册),2019,55(10):718-721.
【3】腾巍,梁博,孙晓庭,等. 42CrMo钢高强度螺栓轴向开裂失效分析[J]. 理化检验(物理分册),2017,53(4):296-298.
【4】张栋,钟培德,陶春虎,等. 失效分析[M]. 北京:国防工业出版社,2004.
【5】钟群鹏,赵子华. 断口学[M]. 北京:高等教育出版社,2006.
【6】钟群鹏,周煜,张峥. 裂纹学[M]. 北京:高等教育出版社,2014.
相关信息