Determination of Nine Elements in Wire by Spark Source Atomic Emission Spectroscopy
摘 要
建立了火花源原子发射光谱法测定直径为8~12 mm的小规格线材中的碳、硅、锰、磷、硫、镍、铬、铜和钒等9种元素含量的方法。试样经切割和打磨后,按规格及钢种选择对应的自制夹具固定,垂直于磨样机打磨试样的端面。用随V型板专用的定位夹具将样品定位在火花源原子发射光谱仪激发孔中心位置,使试样支架中心和电极中心对齐。盖好顶盖,用氩气吹扫火花室5 s,采用能量为0.2 J、频率为100 Hz激发光激发样品。在优化的仪器工作条件下,试样中9种元素可在10 min内完成测定。采用块状光谱国家标准样品制作校准曲线,用校正公式消除了共存元素的干扰及由标准试样和实际试样形状差异带来的系统偏差。结果显示:9种元素的质量分数均在一定范围内与其对应的响应值呈线性关系,检出限(3s)为1.5~18.1 μg·g-1;用此方法分析实际样品,所得测定值与参考文献使用的其他方法的基本一致,测定值的相对标准偏差(n=11)均在5%以内。
Abstract
A method was developed for the determination of 9 elements (including carbon, silicon, manganese, phosphorus, sulfur, nickel, chromium, copper, and vanadium) in small size wire with the diameter of 8-12 mm by spark source atomic emission spectroscopy. After cutting and polishing, the sample was fixed by the self-made fixture according to the specification and steel type, to grind the end face of the sample perpendicular to the sample grinding machine. The sample was positioned at the center of the excitation hole of the spark source of atomic emission spectrometer with a special fixture attached to the v-shaped plate to keep the center of the sample support aligned with the center of the electrode. The sample was excited by 0.2 J excitation laser at 100 Hz after the spark chamber was swept with argon gas for 5 s. Under the optimum working conditions of the instrument, the determination of 9 elements in the sample could be completed within 10 min. The calibration curves were made by using the national standard sample of block spectrum, and the interference of coexisting elements and the systematic deviation caused by the shape difference between standard sample and actual sample were eliminated by using the calibration formula. The results showed that linearity relationships between mass fractions of 9 elements and their corresponding response values were kept in the definite ranges, with detection limits (3s) in the range of 1.5-18.1μg·g-1. The proposed method was used for determination of the actual samples, determined values obtained were in conformity to those of other methods from reference, and RSDs (n=11) of the determined values were all less than 5%.
中图分类号 O657.31 DOI 10.11973/lhjy-hx202103012
所属栏目 工作简报
基金项目
收稿日期 2020/3/19
修改稿日期
网络出版日期
作者单位点击查看
备注杨再军,工程师,主要从事检测方法优化与实验室管理工作,pzhyzaijun@126.com
引用该论文: YANG Zaijun,DIAO Zhengbin,WANG Juan,YANG Shaosong. Determination of Nine Elements in Wire by Spark Source Atomic Emission Spectroscopy[J]. Physical Testing and Chemical Analysis part B:Chemical Analysis, 2021, 57(3): 258~263
杨再军,刁正斌,王娟,羊绍松. 火花源原子发射光谱法测定线材中9种元素[J]. 理化检验-化学分册, 2021, 57(3): 258~263
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】中华人民共和国国家质量监督检验检疫总局,中国国家标准化管理委员会.钢筋混凝土用钢第2部分:热轧带肋钢筋:GB/T 1499.2-2018[S].北京:中国标准出版社, 2008.
【2】王娇娜,周西林,王亚森,等.冷压塑形制样-光电直读光谱法测定碳素钢钢丝中C、Si、Mn、P、S、Cr、Ni、Cu的含量[J].理化检验-化学分册, 2019,55(9):1107-1111.
【3】中华人民共和国国家质量监督检验检疫总局,中国国家标准化管理委员会.低合金钢多元素的测定电感耦合等离子体发射光谱法:GB/T 20125-2006[S].北京:中国标准出版社, 2006.
【4】中华人民共和国国家质量监督检验检疫总局,中国国家标准化管理委员会.碳素钢和中低合金钢多元素含量的测定火花放电原子发射光谱法(常规法):GB/T 4336-2016[S].北京:中国标准出版社, 2016.
【5】董利珍,祁世明,崔军.ICP-AES法测定普碳钢及低合金钢中铝等23种元素[J].冶金分析, 2001,21(5):27-30.
【6】刘翔,沈克,郭芳,等.高速线材的化学成分分析[J].武钢技术, 2001,39(4):15-18.
【7】杨忠梅.火花源原子发射光谱仪分析小样品[J].冶金分析, 2007,27(3):61-64.
【8】吴宗平.小断面棒样中9种元素的光谱法测定[J].四川冶金, 2014,36(4):74-76.
【9】付志军,罗桂娟,刘云平,等.火花源原子发射光谱法测定螺纹钢中铌.[J].冶金分析, 2007,27(5):75-77.
【10】宋祖峰,程坚平.不锈钢线材的火花源原子发射光谱分析[J].安徽冶金, 2005(1):30-33.
【11】张兵,岳锋涛.高碳钢线材化学成分分析研究[J].金属制品, 2005,31(5):48-50.
【12】戴亚明,张宏鹤,鄢国强,等.直读原子发射光谱综合小试样程序分析可靠性研究[J].现代科学仪器, 2008(6):70-75.
【13】韩宗才,兰恩有,丁彦风,等.小直径不锈钢棒样品的火花源原子发射光谱分析[J].冶金分析, 2014,34(9):24-28.
【14】赵兰季.光电直读光谱法测定小规格线材试样中碳、硅、锰、磷和硫的含量[J].理化检验-化学分册, 2014,50(2):169-171.
【2】王娇娜,周西林,王亚森,等.冷压塑形制样-光电直读光谱法测定碳素钢钢丝中C、Si、Mn、P、S、Cr、Ni、Cu的含量[J].理化检验-化学分册, 2019,55(9):1107-1111.
【3】中华人民共和国国家质量监督检验检疫总局,中国国家标准化管理委员会.低合金钢多元素的测定电感耦合等离子体发射光谱法:GB/T 20125-2006[S].北京:中国标准出版社, 2006.
【4】中华人民共和国国家质量监督检验检疫总局,中国国家标准化管理委员会.碳素钢和中低合金钢多元素含量的测定火花放电原子发射光谱法(常规法):GB/T 4336-2016[S].北京:中国标准出版社, 2016.
【5】董利珍,祁世明,崔军.ICP-AES法测定普碳钢及低合金钢中铝等23种元素[J].冶金分析, 2001,21(5):27-30.
【6】刘翔,沈克,郭芳,等.高速线材的化学成分分析[J].武钢技术, 2001,39(4):15-18.
【7】杨忠梅.火花源原子发射光谱仪分析小样品[J].冶金分析, 2007,27(3):61-64.
【8】吴宗平.小断面棒样中9种元素的光谱法测定[J].四川冶金, 2014,36(4):74-76.
【9】付志军,罗桂娟,刘云平,等.火花源原子发射光谱法测定螺纹钢中铌.[J].冶金分析, 2007,27(5):75-77.
【10】宋祖峰,程坚平.不锈钢线材的火花源原子发射光谱分析[J].安徽冶金, 2005(1):30-33.
【11】张兵,岳锋涛.高碳钢线材化学成分分析研究[J].金属制品, 2005,31(5):48-50.
【12】戴亚明,张宏鹤,鄢国强,等.直读原子发射光谱综合小试样程序分析可靠性研究[J].现代科学仪器, 2008(6):70-75.
【13】韩宗才,兰恩有,丁彦风,等.小直径不锈钢棒样品的火花源原子发射光谱分析[J].冶金分析, 2014,34(9):24-28.
【14】赵兰季.光电直读光谱法测定小规格线材试样中碳、硅、锰、磷和硫的含量[J].理化检验-化学分册, 2014,50(2):169-171.
相关信息