Effect of Traverse Speed on Microstructure and Properties of High-Entropy Alloy Reinforced Aluminum Matrix Composite by Friction Stir Processing
摘 要
采用搅拌摩擦加工技术制备了FeCoNiCrAl高熵合金颗粒增强AA5083铝基复合材料,研究了行进速度(45,60,75 mm·min-1)对复合材料中高熵合金颗粒分布、显微硬度和耐磨性能的影响。结果表明:制备的复合材料中没有新相生成,复合材料的显微硬度高于铝合金基体的;随着行进速度的增加,高熵合金颗粒的分布均匀性变差,复合材料的显微硬度略微降低;复合材料的平均摩擦因数和磨损率均较铝合金基体的低;随着行进速度的增加,复合材料摩擦因数和磨损率均增大,耐磨性能下降;复合材料和铝合金的磨损机制分别为磨粒磨损和黏着磨损。
Abstract
AA5083 aluminum matrix composite reinforced by FeCoNiCrAl high-entropy alloy particles were prepared by friction stir processing. The effect of the traverse speeds (45,60,75 mm·min-1) on the high-entropy alloy particle distribution, microhardness and wear resistance of the composite was studied. The results show that no new phases were formed in the prepared composite. The microhardness of the composite was higher than that of the aluminum alloy matrix. With the increase of the traverse speed, the distribution uniformity of the high-entropy alloy particles became worse and the microhardness of the composite decreased slightly. The average friction coefficient and wear rate of the composite were lower than those of the aluminum alloy matrix. With the increase of the traverse speed, the friction coefficient and wear rate of the composite increased, and the wear resistance decreased. The wear mechanisms of the composite and aluminum alloy were abrasive wear and adhesive wear, respectively.
中图分类号 TB333 DOI 10.11973/jxgccl202108011
所属栏目 材料性能及应用
基金项目 扬州大学大学生科创基金资助项目(X20200359);扬州大学教学改革研究课题(YZUJX2019-19B);扬州大学科技创新培育基金资助项目(2019CXJ046);江苏省高等学校自然科学研究项目(18KJB460031);中国博士后科学基金面上资助项目(2018M642337)
收稿日期 2020/8/20
修改稿日期 2021/6/24
网络出版日期
作者单位点击查看
备注高吉成(1984-),男,河北衡水人,讲师,博士
引用该论文: GAO Jicheng,GU Gan,ZHONG Shang,DONG Jiachen,ZHANG Sunyi. Effect of Traverse Speed on Microstructure and Properties of High-Entropy Alloy Reinforced Aluminum Matrix Composite by Friction Stir Processing[J]. Materials for mechancial engineering, 2021, 45(8): 61~65
高吉成,顾淦,仲尚,董嘉辰,张孙艺. 行进速度对搅拌摩擦加工高熵合金增强铝基复合材料组织与性能的影响[J]. 机械工程材料, 2021, 45(8): 61~65
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】GARCÍA-BERNAL M A,MISHRA R S,VERMA R,et al.Hot deformation behavior of friction-stir processed strip-cast 5083 aluminum alloys with different Mn contents[J].Materials Science and Engineering:A,2012,534:186-192.
【2】陈玉华,刘东亚,余亮,等.搅拌摩擦加工法制备碳纳米管增强镁基复合材料的组织与性能[J].南昌航空大学学报(自然科学版),2015,29(1):49-54. CHEN Y H,LIU D Y,YU L,et al.Microstructure and microstructure of carbon nanotube reinforced magnesium matrix composites fabricated by friction stir processing[J].Journal of Nanchang Hangkong University (Natural Sciences),2015,29(1):49-54.
【3】瞿皎,陈靓瑜,孟强,等.工业纯钛板多道次搅拌摩擦加工区的组织及摩擦磨损性能[J].机械工程材料,2016,40(5):92-95. QU J,CHEN L Y,MENG Q,et al.Microstructure and friction and wear properties of multi-pass friction stir processed zone of commercial pure titanium plates[J].Materials for Mechanical Engineering,2016,40(5):92-95.
【4】张金凯,程萌旗,魏兴乔,等.搅拌摩擦加工制备TC4钛合金表面载银层的组织形貌和力学性能[J].机械工程材料,2017,41(6):63-68. ZHANG J K,CHENG M Q,WEI X Q,et al.Microstructure and mechanical properties of silver-loaded layer on surface of TC4 alloy prepared by friction stir processing[J].Materials for Mechanical Engineering,2017,41(6):63-68.
【5】李安敏,徐飞,郭宝航,等.AlNiFeCuCoCrVx高熵合金的显微组织与力学性能[J].机械工程材料,2019,43(4):48-52. LI A M,XU F,GUO B H,et al.Microstructure and mechanical properties of AlNiFeCuCoCrVx high-entropy alloy[J].Materials for Mechanical Engineering,2019,43(4):48-52.
【6】姚瑞敏,郑留伟.烧结温度对放电等离子烧结AlCoCrFeNi2.1高熵合金性能的影响[J].机械工程材料,2019,43(7):28-32. YAO R M,ZHENG L W.Effects of sintering temperature on properties of AlCoCrFeNi2.1 high-entropy alloy by spark plasma sintering[J].Materials for Mechanical Engineering,2019,43(7):28-32.
【7】于芮,李紫勇,付立铭,等.添加铝对不同处理态FeCoCrNiMn高熵合金显微组织及电化学性能的影响[J].机械工程材料,2019,43(2):1-6. YU R,LI Z Y,FU L M,et al.Effects of Al addition on microstructure and electrochemical property of FeCoCrNiMn high-entropy alloy in different treatment states[J].Materials for Mechanical Engineering,2019,43(2):1-6.
【8】LIU Y Z,CHEN J,LI Z,et al.Formation of transition layer and its effect on mechanical properties of AlCoCrFeNi high-entropy alloy/Al composites[J].Journal of Alloys and Compounds,2019,780:558-564.
【9】YUAN Z W,TIAN W B,LI F G,et al.Microstructure and properties of high-entropy alloy reinforced aluminum matrix composites by spark plasma sintering[J].Journal of Alloys and Compounds,2019,806:901-908.
【10】LU T W,CHEN W P,LI Z X,et al.Processing and mechanical properties of fine grained Al matrix composites reinforced with a uniform dispersion of nanocrystalline high-entropy alloy particles[J].Journal of Alloys and Compounds,2019,801:473-477.
【11】YANG X,YAN Z F,DONG P,et al.Surface modification of aluminum alloy by incorporation of AlCoCrFeNi high entropy alloy particles via underwater friction stir processing[J].Surface and Coatings Technology,2020,385:125438.
【12】YANG X,DONG P,YAN Z F,et al.AlCoCrFeNi high-entropy alloy particle reinforced 5083Al matrix composites with fine grain structure fabricated by submerged friction stir processing[J].Journal of Alloys and Compounds,2020,836:155411.
【13】WANG T H,KOMARASAMY M,SHUKLA S,et al.Simultaneous enhancement of strength and ductility in an AlCoCrFeNi2.1 eutectic high-entropy alloy via friction stir processing[J].Journal of Alloys and Compounds,2018,766:312-317.
【2】陈玉华,刘东亚,余亮,等.搅拌摩擦加工法制备碳纳米管增强镁基复合材料的组织与性能[J].南昌航空大学学报(自然科学版),2015,29(1):49-54. CHEN Y H,LIU D Y,YU L,et al.Microstructure and microstructure of carbon nanotube reinforced magnesium matrix composites fabricated by friction stir processing[J].Journal of Nanchang Hangkong University (Natural Sciences),2015,29(1):49-54.
【3】瞿皎,陈靓瑜,孟强,等.工业纯钛板多道次搅拌摩擦加工区的组织及摩擦磨损性能[J].机械工程材料,2016,40(5):92-95. QU J,CHEN L Y,MENG Q,et al.Microstructure and friction and wear properties of multi-pass friction stir processed zone of commercial pure titanium plates[J].Materials for Mechanical Engineering,2016,40(5):92-95.
【4】张金凯,程萌旗,魏兴乔,等.搅拌摩擦加工制备TC4钛合金表面载银层的组织形貌和力学性能[J].机械工程材料,2017,41(6):63-68. ZHANG J K,CHENG M Q,WEI X Q,et al.Microstructure and mechanical properties of silver-loaded layer on surface of TC4 alloy prepared by friction stir processing[J].Materials for Mechanical Engineering,2017,41(6):63-68.
【5】李安敏,徐飞,郭宝航,等.AlNiFeCuCoCrVx高熵合金的显微组织与力学性能[J].机械工程材料,2019,43(4):48-52. LI A M,XU F,GUO B H,et al.Microstructure and mechanical properties of AlNiFeCuCoCrVx high-entropy alloy[J].Materials for Mechanical Engineering,2019,43(4):48-52.
【6】姚瑞敏,郑留伟.烧结温度对放电等离子烧结AlCoCrFeNi2.1高熵合金性能的影响[J].机械工程材料,2019,43(7):28-32. YAO R M,ZHENG L W.Effects of sintering temperature on properties of AlCoCrFeNi2.1 high-entropy alloy by spark plasma sintering[J].Materials for Mechanical Engineering,2019,43(7):28-32.
【7】于芮,李紫勇,付立铭,等.添加铝对不同处理态FeCoCrNiMn高熵合金显微组织及电化学性能的影响[J].机械工程材料,2019,43(2):1-6. YU R,LI Z Y,FU L M,et al.Effects of Al addition on microstructure and electrochemical property of FeCoCrNiMn high-entropy alloy in different treatment states[J].Materials for Mechanical Engineering,2019,43(2):1-6.
【8】LIU Y Z,CHEN J,LI Z,et al.Formation of transition layer and its effect on mechanical properties of AlCoCrFeNi high-entropy alloy/Al composites[J].Journal of Alloys and Compounds,2019,780:558-564.
【9】YUAN Z W,TIAN W B,LI F G,et al.Microstructure and properties of high-entropy alloy reinforced aluminum matrix composites by spark plasma sintering[J].Journal of Alloys and Compounds,2019,806:901-908.
【10】LU T W,CHEN W P,LI Z X,et al.Processing and mechanical properties of fine grained Al matrix composites reinforced with a uniform dispersion of nanocrystalline high-entropy alloy particles[J].Journal of Alloys and Compounds,2019,801:473-477.
【11】YANG X,YAN Z F,DONG P,et al.Surface modification of aluminum alloy by incorporation of AlCoCrFeNi high entropy alloy particles via underwater friction stir processing[J].Surface and Coatings Technology,2020,385:125438.
【12】YANG X,DONG P,YAN Z F,et al.AlCoCrFeNi high-entropy alloy particle reinforced 5083Al matrix composites with fine grain structure fabricated by submerged friction stir processing[J].Journal of Alloys and Compounds,2020,836:155411.
【13】WANG T H,KOMARASAMY M,SHUKLA S,et al.Simultaneous enhancement of strength and ductility in an AlCoCrFeNi2.1 eutectic high-entropy alloy via friction stir processing[J].Journal of Alloys and Compounds,2018,766:312-317.
相关信息