Cause of Fracture on Large Spring in a Hydraulic System
摘 要
某液压系统使用的大型圆柱螺旋压缩弹簧在运行20万次后发生断裂,采用断口形貌、显微组织观察,化学成分、硬度测试等方法对弹簧的断裂原因进行了分析。结果表明:弹簧的断裂为低周疲劳断裂,裂纹源区位于弹簧钢丝近表面位置的大尺寸夹杂物处;夹杂物的存在降低了弹簧钢内部的连续性,弹簧钢受到拉应力和扭转作用力时萌生裂纹,在后续服役过程中裂纹扩展,最终断裂;弹簧喷丸处理形成的硬化层深度不够,不足以抵消弹簧钢丝表面脱碳层对疲劳寿命的不利影响,导致疲劳寿命降低。
Abstract
A large cylindrical spiral compression spring used in a hydraulic system was fractured after operating 200 000 times. The causes of fracture on spring were analyzed by fracture morphology, microstructure observation, and chemical composition and hardness test. The results show that the fracture of the spring was low cycle fatigue fracture, and the crack source region was located at the large inclusions near the surface of the spring steel wire. The existence of inclusions reduced the internal continuity of the spring steel, and cracks initiated when the spring steel was subjected to tensile stress and torsional force, and the cracks expanded in the subsequent service process, eventually fracture. The depth of hardening layer formed during peening was not enough to effset the adverse effect of decarbonized layer on fatigue life of spring steel wire, resulting in the reduction of fatigue life.
中图分类号 TG142.1 DOI 10.11973/lhjy-wl202109015
所属栏目 质量控制与失效分析
基金项目
收稿日期 2020/9/14
修改稿日期
网络出版日期
作者单位点击查看
备注袁萍(1977-),女,工程师,主要从事金属材料测试及失效分析工作,lily.yuan@sgs.com
引用该论文: YUAN Ping,CHEN Yi,WANG Jingde. Cause of Fracture on Large Spring in a Hydraulic System[J]. Physical Testing and Chemical Analysis part A:Physical Testing, 2021, 57(9): 64~67
袁萍,陈怡,王敬德. 某液压系统大型弹簧断裂原因[J]. 理化检验-物理分册, 2021, 57(9): 64~67
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】张栋, 钟培道, 陶春虎, 等.失效分析[M].北京:国防工业出版社, 2004.
【2】王荣.失效分析应用技术[M].北京:机械工业出版社, 2019.
【3】陈德和.钢的缺陷[M].北京:机械工业出版社, 1977.
【4】苏德达, 李忆莲.弹簧的失效分析[M].北京:机械工业出版社, 1988:205-215.
【5】吴睿, 张晓清, 侯丽华.65Si2MnWA弹簧钢线状缺陷分析[J].理化检验(物理分册), 2016, 52(6):435-437.
【6】胡世炎.机械失效分析手册[M].成都:四川科学技术出版社, 1989.
【2】王荣.失效分析应用技术[M].北京:机械工业出版社, 2019.
【3】陈德和.钢的缺陷[M].北京:机械工业出版社, 1977.
【4】苏德达, 李忆莲.弹簧的失效分析[M].北京:机械工业出版社, 1988:205-215.
【5】吴睿, 张晓清, 侯丽华.65Si2MnWA弹簧钢线状缺陷分析[J].理化检验(物理分册), 2016, 52(6):435-437.
【6】胡世炎.机械失效分析手册[M].成都:四川科学技术出版社, 1989.
相关信息