Test error of texture of 3104 aluminum alloy by X-ray diffraction
摘 要
利用X射线衍射法对3种不同热处理状态的3104铝合金试样进行织构测试,并对其织构的体积分数测试误差进行分析。结果表明:X射线衍射法检测试样的倾斜角为50°时,利用任意单包法计算织构的体积分数误差基本趋于稳定,合理选择X射线衍射法的倾斜角可节省测试时间和保证体积分数测试误差在可接受范围内。
Abstract
The texture of 3104 aluminum alloy samples with three different heat treatment states was tested by X-ray diffraction method, and the volume fraction test error of the texture was analyzed. The results show that when the inclination angle of X-ray diffraction test sample was 50°, the volume fraction error of texture calculated by ADC method basically tended to be stable. Reasonable selection of inclination angle of X-ray diffraction test sample could save test time and ensure volumn fraction measurement error within acceptable range.
中图分类号 TG115.5 DOI 10.11973/lhjy-wl202204006
所属栏目 试验与研究
基金项目
收稿日期 2021/8/6
修改稿日期
网络出版日期
作者单位点击查看
备注董学光(1985-),男,博士,高级工程师,主要从事透射电镜、扫描电镜和X射线衍射微观组织测试技术研究工作,dxg1985123@163.com
引用该论文: DONG Xueguang,ZOU Liying,WANG Meimei,GU Ningjie,HE Minglan. Test error of texture of 3104 aluminum alloy by X-ray diffraction[J]. Physical Testing and Chemical Analysis part A:Physical Testing, 2022, 58(4): 19~22
董学光,邹立颖,王眉眉,谷宁杰,贺铭兰. 3104铝合金织构的X射线衍射法测试误差[J]. 理化检验-物理分册, 2022, 58(4): 19~22
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】杨中玉, 张津,郭学博,等. 铝合金的织构及测试分析研究进展[J]. 精密成形工程,2013,5(6):1-6,47.
【2】熊彪. 3003铝合金材料制耳率的控制[J]. 铝加工,2020(1):34-37.
【3】ENGLER O. Texture and anisotropy in the Al-Mg alloy AA 5005 - Part I:texture evolution during rolling and recrystallization[J]. Materials Science and Engineering:A,2014,618:654-662.
【4】HUTCHINSON W B,OSCARSSON A,KARLSSON. Control of microstructure and earing behaviour in aluminium alloy AA 3004 hot bands[J]. Materials Science and Technology,1989,5(11):1118-1127.
【5】黄丽颖. 稀土电解电容器高压阳极用铝箔组织和织构研究[D]. 包头:内蒙古科技大学,2007.
【6】马礼敦.X射线衍射在材料结构表征中的应用[J].理化检验(物理分册),2009,45(8):501-510.
【7】ROE R J. Description of crystallite orientation in polycrystalline materials. III. general solution to pole figure inversion[J]. Journal of Applied Physics,1965,36(6):2024-2031.
【8】张克龙,张继祥,刘运腾,等. 6016铝合金冷轧显微组织和织构的演变[J]. 稀有金属材料与工程,2017,46(6):1559-1565.
【9】夏柳,徐春,白清领,等. 退火后终轧压下量对铝合金轧板织构和深冲性能的影响[J]. 上海金属,2019,41(2):29-34.
【10】毛卫民. 金属材料的晶体学织构与各向异性[M]. 北京:科学出版社,2002.
【11】汪波,易丹青,陈宇强,等. 2E12铝合金在冷轧和退火过程中织构和显微组织的演变[J]. 中国有色金属学报,2013,23(11):3064-3074.
【12】沈健,张新明. 中间退火对3004合金组织、织构和各向异性的影响[J]. 铝加工,1994(3):44-47,63.
【13】陈志永,才鸿年,常亚喆,等. 多晶铝轧制变形的织构演变 Ⅰ. 实验研究[J]. 金属学报,2008,44(11):1316-1321.
【2】熊彪. 3003铝合金材料制耳率的控制[J]. 铝加工,2020(1):34-37.
【3】ENGLER O. Texture and anisotropy in the Al-Mg alloy AA 5005 - Part I:texture evolution during rolling and recrystallization[J]. Materials Science and Engineering:A,2014,618:654-662.
【4】HUTCHINSON W B,OSCARSSON A,KARLSSON. Control of microstructure and earing behaviour in aluminium alloy AA 3004 hot bands[J]. Materials Science and Technology,1989,5(11):1118-1127.
【5】黄丽颖. 稀土电解电容器高压阳极用铝箔组织和织构研究[D]. 包头:内蒙古科技大学,2007.
【6】马礼敦.X射线衍射在材料结构表征中的应用[J].理化检验(物理分册),2009,45(8):501-510.
【7】ROE R J. Description of crystallite orientation in polycrystalline materials. III. general solution to pole figure inversion[J]. Journal of Applied Physics,1965,36(6):2024-2031.
【8】张克龙,张继祥,刘运腾,等. 6016铝合金冷轧显微组织和织构的演变[J]. 稀有金属材料与工程,2017,46(6):1559-1565.
【9】夏柳,徐春,白清领,等. 退火后终轧压下量对铝合金轧板织构和深冲性能的影响[J]. 上海金属,2019,41(2):29-34.
【10】毛卫民. 金属材料的晶体学织构与各向异性[M]. 北京:科学出版社,2002.
【11】汪波,易丹青,陈宇强,等. 2E12铝合金在冷轧和退火过程中织构和显微组织的演变[J]. 中国有色金属学报,2013,23(11):3064-3074.
【12】沈健,张新明. 中间退火对3004合金组织、织构和各向异性的影响[J]. 铝加工,1994(3):44-47,63.
【13】陈志永,才鸿年,常亚喆,等. 多晶铝轧制变形的织构演变 Ⅰ. 实验研究[J]. 金属学报,2008,44(11):1316-1321.
相关信息