后处理工艺对激光选区熔化成形Hastelloy-X合金显微组织和低周疲劳性能的影响
Effect of Post Treatment Process on Microstructure and Low Cycle Fatigue Properties of Selective Laser Melting Formed Hastelloy-X Alloy
摘 要
采用激光选区熔化(SLM)技术制备Hastelloy-X合金,研究了不同的后处理工艺(1 175℃×2 h固溶处理、1 175℃/150 MPa×1 h或1 175℃/150 MPa×2 h热等静压处理)对合金显微组织和低周疲劳性能的影响。结果表明:SLM成形合金具备典型的熔池边界形貌和由细小树枝晶构成的柱状晶组织,同时存在微裂纹、气孔、孔洞等冶金缺陷;固溶处理消除了合金熔池边界,且晶粒由柱状晶向等轴晶转变,热等静压处理则能进一步闭合合金中的裂纹和气孔,同时沿晶界析出不连续的细小M6C型碳化物;相比于固溶态合金,热等静压态合金具有更好的低周疲劳性能,其中2 h热等静压时间下得到的合金低周疲劳寿命略高;固溶处理态合金的疲劳裂纹以穿晶形式扩展,而热等静压态合金以穿晶+沿晶混合模式扩展。
Hastelloy-X合金
热等静压
低周疲劳
selective laser melting
Hastelloy-X alloy
hot isostatic pressing
low cycle fatigue
Abstract
Hastelloy-X alloy was fabricated by selective laser melting (SLM) process, and the effects of different post treatment processes (solution treatment of 1 175℃×2 h, hot isostatic pressing of 1 175℃/150 MPa×1 h or 1 175℃/150 MPa×2 h) on the microstructure and low cycle fatigue properties of the alloy were studied. The results show that the SLM formed alloy had a typical molten pool boundary morphology and a columnar crystal structure composed of fine dendrites, and there were metallurgical defects such as microcracks, pores and holes. Solution treatment eliminated the boundary of the alloy molten pool, and the grains transformed from columnar to equiaxed. Hot isostatic pressing could further close the cracks and pores in the alloy, and small discontinuous M6C carbides precipitated along the grain boundaries. Compared with solution treated alloy, hot isostatic pressed alloy had better low cycle fatigue properties, and the low cycle fatigue life of the alloy obtained under 2 h hot isostatic pressing time was slightly higher. Fatigue cracks propagated in a transgranular manner for solution treated alloy, while propagated in a mixed transgranular+intergranular mode for hot isostatic pressed alloy.
中图分类号 TG146.1+5 DOI 10.11973/jxgccl202208007
所属栏目 试验研究
基金项目
收稿日期 2021/6/3
修改稿日期 2022/6/20
网络出版日期
作者单位点击查看
备注潘敏(1995-),女,江苏宿迁人,工程师,硕士
引用该论文: PAN Min,ZHANG Hongqi,TAN Luyi. Effect of Post Treatment Process on Microstructure and Low Cycle Fatigue Properties of Selective Laser Melting Formed Hastelloy-X Alloy[J]. Materials for mechancial engineering, 2022, 46(8): 40～45
潘敏,张宏琦,谈芦益. 后处理工艺对激光选区熔化成形Hastelloy-X合金显微组织和低周疲劳性能的影响[J]. 机械工程材料, 2022, 46(8): 40～45
共有人对该论文发表了看法，其中：
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】WANG F D.Mechanical property study on rapid additive layer manufacture Hastelloy® X alloy by selective laser melting technology[J].The International Journal of Advanced Manufacturing Technology,2012,58(5/6/7/8):545-551.
【2】WANG F,WU X H,CLARK D.On direct laser deposited Hastelloy X:Dimension,surface finish,microstructure and mechanical properties[J].Materials Science and Technology,2011,27(1):344-356.
【3】TIAN Y,TOMUS D,ROMETSCH P,et al.Influences of processing parameters on surface roughness of Hastelloy X produced by selective laser melting[J].Additive Manufacturing,2017,13:103-112.
【4】TOMUS D,TIAN Y,ROMETSCH P A,et al.Influence of post heat treatments on anisotropy of mechanical behaviour and microstructure of Hastelloy-X parts produced by selective laser melting[J].Materials Science and Engineering:A,2016,667:42-53.
【5】侯慧鹏,梁永朝,何艳丽,等.选区激光熔化Hastelloy-X合金组织演变及拉伸性能[J].中国激光,2017,44(2):0202007.HOU H P,LIANG Y C,HE Y L,et al.Microstructural evolution and tensile property of Hastelloy-X alloys produced by selective laser melting[J].Chinese Journal of Lasers,2017,44(2):0202007.
【6】李勇,许鹤君,李凯,等.体能量密度对选区激光熔化成形Hastelloy X合金组织及性能的影响[J].机械工程材料,2020,44(5):38-43.LI Y,XU H J,LI K,et al.Effect of volumetric energy density on microstructure and properties of Hastelloy X alloy manufactured by selective laser melting[J].Materials for Mechanical Engineering,2020,44(5):38-43.
【7】LI Y L,QI H,HOU H P,et al.Effects of hot isostatic pressing on microstructure and mechanical properties of Hastelloy X samples produced by selective laser melting[J].Advances in Engineering Research, 2017, 102:31-40.
【8】廖文俊,樊恩想,付超.激光选区熔化Hastelloy-X合金的显微组织与拉伸性能[J].机械工程材料,2018,42(7):16-22.LIAO W J,FAN E X,FU C.Microstructure and tensile properties of Hastelloy-X alloy prepared by selective laser melting[J].Materials for Mechanical Engineering,2018,42(7):16-22.
【9】刘凯,王荣,祁海,等.选区激光熔化成型GH3536合金的显微组织与拉伸性能[J].理化检验(物理分册),2019,55(1):15-18.LIU K,WANG R,QI H,et al.Microstructure and tensile properties of GH3536 alloy formed by SLM[J].Physical Testing and Chemical Analysis (Part A:Physical Testing),2019,55(1):15-18.
【10】孙闪闪,滕庆,程坦,等.热处理对激光选区熔化GH3536合金组织演变规律的影响研究[J].机械工程学报,2020,56(21):208-218.SUN S S,TENG Q,CHENG T,et al.Influence of heat treatment on microstructure evolution of GH3536 superalloy fabricated by selective laser melting[J].Journal of Mechanical Engineering,2020,56(21):208-218.
【11】许鹤君,李勇,祁海,等.热等静压工艺对选区激光熔化成形Hastelloy X合金持久性能的影响[J].机械工程材料,2018,42(12):53-57.XU H J,LI Y,QI H,et al.Effect of hot isostatic pressing process on stress-rupture property of Hastelloy X alloy by selective laser melting[J].Materials for Mechanical Engineering,2018,42(12):53-57.
【12】郭建亭.高温合金材料学[M].北京:科学出版社,2008.GUO J T.Materials science and engineering for superalloys[M].Beijing:Science Press,2008:363-374.
【13】BELAN J.GCP and TCP phases presented in nickel-base superalloys[J].Materials Today:Proceedings,2016,3(4):936-941.
【14】ZHAO J C,LARSEN M,RAVIKUMAR V.Phase precipitation and time-temperature-transformation diagram of Hastelloy X[J].Materials Science and Engineering:A,2000,293(1/2):112-119.
【15】李慧英,胡本芙,章守华.原粉末颗粒边界碳化物的研究[J].金属学报,1987,23(2):212-216.LI H Y,HU B F,ZHANG S H.Study of previous powder-particle boundary carbides[J].Acta Metallurgica Sinica,1987,23(2):212-216.
【16】MARCHESE G,BASSINI E,AVERSA A,et al.Microstructural evolution of post-processed Hastelloy X alloy fabricated by laser powder bed fusion[J].Materials (Basel,Switzerland),2019,12(3):E486.
【17】TOMUS D,JARVIS T,WU X,et al.Controlling the microstructure of Hastelloy-X components manufactured by selective laser melting[J].Physics Procedia,2013,41:823-827.
【2】WANG F,WU X H,CLARK D.On direct laser deposited Hastelloy X:Dimension,surface finish,microstructure and mechanical properties[J].Materials Science and Technology,2011,27(1):344-356.
【3】TIAN Y,TOMUS D,ROMETSCH P,et al.Influences of processing parameters on surface roughness of Hastelloy X produced by selective laser melting[J].Additive Manufacturing,2017,13:103-112.
【4】TOMUS D,TIAN Y,ROMETSCH P A,et al.Influence of post heat treatments on anisotropy of mechanical behaviour and microstructure of Hastelloy-X parts produced by selective laser melting[J].Materials Science and Engineering:A,2016,667:42-53.
【5】侯慧鹏,梁永朝,何艳丽,等.选区激光熔化Hastelloy-X合金组织演变及拉伸性能[J].中国激光,2017,44(2):0202007.HOU H P,LIANG Y C,HE Y L,et al.Microstructural evolution and tensile property of Hastelloy-X alloys produced by selective laser melting[J].Chinese Journal of Lasers,2017,44(2):0202007.
【6】李勇,许鹤君,李凯,等.体能量密度对选区激光熔化成形Hastelloy X合金组织及性能的影响[J].机械工程材料,2020,44(5):38-43.LI Y,XU H J,LI K,et al.Effect of volumetric energy density on microstructure and properties of Hastelloy X alloy manufactured by selective laser melting[J].Materials for Mechanical Engineering,2020,44(5):38-43.
【7】LI Y L,QI H,HOU H P,et al.Effects of hot isostatic pressing on microstructure and mechanical properties of Hastelloy X samples produced by selective laser melting[J].Advances in Engineering Research, 2017, 102:31-40.
【8】廖文俊,樊恩想,付超.激光选区熔化Hastelloy-X合金的显微组织与拉伸性能[J].机械工程材料,2018,42(7):16-22.LIAO W J,FAN E X,FU C.Microstructure and tensile properties of Hastelloy-X alloy prepared by selective laser melting[J].Materials for Mechanical Engineering,2018,42(7):16-22.
【9】刘凯,王荣,祁海,等.选区激光熔化成型GH3536合金的显微组织与拉伸性能[J].理化检验(物理分册),2019,55(1):15-18.LIU K,WANG R,QI H,et al.Microstructure and tensile properties of GH3536 alloy formed by SLM[J].Physical Testing and Chemical Analysis (Part A:Physical Testing),2019,55(1):15-18.
【10】孙闪闪,滕庆,程坦,等.热处理对激光选区熔化GH3536合金组织演变规律的影响研究[J].机械工程学报,2020,56(21):208-218.SUN S S,TENG Q,CHENG T,et al.Influence of heat treatment on microstructure evolution of GH3536 superalloy fabricated by selective laser melting[J].Journal of Mechanical Engineering,2020,56(21):208-218.
【11】许鹤君,李勇,祁海,等.热等静压工艺对选区激光熔化成形Hastelloy X合金持久性能的影响[J].机械工程材料,2018,42(12):53-57.XU H J,LI Y,QI H,et al.Effect of hot isostatic pressing process on stress-rupture property of Hastelloy X alloy by selective laser melting[J].Materials for Mechanical Engineering,2018,42(12):53-57.
【12】郭建亭.高温合金材料学[M].北京:科学出版社,2008.GUO J T.Materials science and engineering for superalloys[M].Beijing:Science Press,2008:363-374.
【13】BELAN J.GCP and TCP phases presented in nickel-base superalloys[J].Materials Today:Proceedings,2016,3(4):936-941.
【14】ZHAO J C,LARSEN M,RAVIKUMAR V.Phase precipitation and time-temperature-transformation diagram of Hastelloy X[J].Materials Science and Engineering:A,2000,293(1/2):112-119.
【15】李慧英,胡本芙,章守华.原粉末颗粒边界碳化物的研究[J].金属学报,1987,23(2):212-216.LI H Y,HU B F,ZHANG S H.Study of previous powder-particle boundary carbides[J].Acta Metallurgica Sinica,1987,23(2):212-216.
【16】MARCHESE G,BASSINI E,AVERSA A,et al.Microstructural evolution of post-processed Hastelloy X alloy fabricated by laser powder bed fusion[J].Materials (Basel,Switzerland),2019,12(3):E486.
【17】TOMUS D,JARVIS T,WU X,et al.Controlling the microstructure of Hastelloy-X components manufactured by selective laser melting[J].Physics Procedia,2013,41:823-827.
相关信息
