Causes of thread gluing of casing thread in a gas well
摘 要
针对某气井套管螺纹粘扣的问题,采用宏观观察、螺纹参数测量、扫描电镜分析等方法对其进行原因分析,并对同类型新套管进行了上、卸扣试验。结果表明:该套管的螺纹参数符合要求;套管螺纹磷化层厚度分布不均匀和套管抗粘扣性能不好是该套管螺纹粘扣的主要原因。
Abstract
In view of the problem of thread gluing of casing thread in a gas well, the macro observation, thread parameter measurement and scanning electron microscope analysis were used to analyze its causes. The screw on and screw off test was carried out on the same type of new casing. The results show that the thread parameters of the casing met the requirements. The uneven thickness distribution of casing thread phosphating layer and poor anti-sticking performance of casing were the main reasons for the thread gluing of casing thread.
中图分类号 TG115.5 DOI 10.11973/lhjy-wl202208019
所属栏目 质量控制与失效分析
基金项目 国家重大科技专项课题(2016ZX05020-002)
收稿日期 2021/12/31
修改稿日期
网络出版日期
作者单位点击查看
备注王帅(1986-),男,硕士,高级工程师,主要从事石油管材失效分析工作,wangshuai6@cnpc.com.cn
引用该论文: WANG Shuai,XIA Xiaohui,LIU Nan,XIAO Feng,KUANG Xianren. Causes of thread gluing of casing thread in a gas well[J]. Physical Testing and Chemical Analysis part A:Physical Testing, 2022, 58(8): 69~72
王帅,夏晓辉,柳楠,肖峰,邝献任. 某气井套管螺纹粘扣原因[J]. 理化检验-物理分册, 2022, 58(8): 69~72
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】张永强,王新虎.油套管螺纹抗粘扣技术研究进展[J].石油矿场机械,2008,37(2):78-81.
【2】史交齐,姬丙寅,刘卜,等.某井特殊螺纹接头粘扣原因分析[J].石油矿场机械,2016,45(3):62-65.
【3】吕拴录,常泽亮,吴富强,等.N80 LCSG套管上、卸扣试验研究[J].理化检验(物理分册),2006,42(12):602-605.
【4】杨向同,吕拴录,彭建新,等.某油井特殊螺纹接头油管粘扣原因分析[J].理化检验(物理分册),2016,52(5):320-323.
【5】吕拴录,李鹤林,藤学清,等.油套管粘扣和泄漏失效分析综述[J].石油矿场机械,2011,40(4):21-25.
【2】史交齐,姬丙寅,刘卜,等.某井特殊螺纹接头粘扣原因分析[J].石油矿场机械,2016,45(3):62-65.
【3】吕拴录,常泽亮,吴富强,等.N80 LCSG套管上、卸扣试验研究[J].理化检验(物理分册),2006,42(12):602-605.
【4】杨向同,吕拴录,彭建新,等.某油井特殊螺纹接头油管粘扣原因分析[J].理化检验(物理分册),2016,52(5):320-323.
【5】吕拴录,李鹤林,藤学清,等.油套管粘扣和泄漏失效分析综述[J].石油矿场机械,2011,40(4):21-25.
相关信息