Reasons for Cracking Failure of an Elbow of External Petroleum Pipeline in a Station
摘 要
塔河油田某站外输油管线弯管出现开裂现象。利用金相显微镜、扫描电镜对失效位置形貌进行观察,通过X衍射分析仪对腐蚀产物进行分析,并对管材力学性能进行测试,明确输油管线弯管的开裂原因。结果表明:管材组织中存在上贝氏体、贝氏体及马氏体等非正常组织,材料强度、硬度偏高,韧塑性偏低;材料中含有少量夹杂,且残余应力较高,使弯管开裂敏感性升高;管道在内应力及腐蚀介质的作用下发生应力腐蚀开裂,随着应力的持续作用,管道发生破裂,出现刺漏。
Abstract
An elbow of external oil pipeline in a station in Tahe oilfield cracked. In order to determine the cracking reason of the oil pipeline elbow, the morphology of failure position were observed by metallographic microscope and scanning electron microscope, the pipeline corrosion products were analyzed by X-ray diffraction, and the mechanical properties of the pipe were tested. The results showed that there were abnormal structures such as upper bainite, bainite and martensite in the microstructure of pipeline, so the material had high strength and hardness, and low plasticity and toughness. A small amount of inclusions and high residual stress in the material caused the improvement of cracking sensitivity of the elbow. Stress corrosion cracking occurred in the pipelines under the action of internal stress and corrosive medium. With the continuous action of stress, the pipeline cracked and leaked.
中图分类号 TG172 DOI 10.11973/fsyfh-202308020
所属栏目 失效分析
基金项目
收稿日期 2021/9/14
修改稿日期
网络出版日期
作者单位点击查看
引用该论文: XU Yanyan,LIU Qingshan,WEN Ninghua,GE Pengli,XIAO Wenwen,WANG Maomao. Reasons for Cracking Failure of an Elbow of External Petroleum Pipeline in a Station[J]. Corrosion & Protection, 2023, 44(8): 111
共有人对该论文发表了看法,其中:
人认为该论文很差
人认为该论文较差
人认为该论文一般
人认为该论文较好
人认为该论文很好
参考文献
【1】李占坤, 孙彪, 王喜乐, 等. 塔河油田油气集输管网腐蚀现状及防腐蚀技术[J]. 腐蚀与防护, 2015, 36(3):240-244, 299.
【2】叶帆, 杨伟. 塔河油田集输管道腐蚀与防腐技术[J]. 油气储运, 2010, 29(5):356-360, 364, 315.
【3】卢智慧, 何雪芹, 何昶. 塔河油田集输管道腐蚀因素及防腐措施[J]. 油气田地面工程, 2015, 34(7):18-20.
【4】赵震, 黄雪峰, 刘强. 塔河油田地面集输处理系统腐蚀穿孔原因[J]. 腐蚀与防护, 2013, 34(5):442-445.
【5】张志宏, 许艳艳, 葛鹏莉, 等. 塔河油田集输管线20#钢在CO2/H2S环境中的腐蚀行为[J]. 工业安全与环保, 2020, 46(1):32-36.
【6】陶勇. 金属材料应力腐蚀裂纹的探讨[J]. 中国教育技术装备, 2013(6):131, 134.
【7】潘卫军. 埋地管道材料的H2S应力腐蚀研究[D]. 南京:南京工业大学, 2004:1-3.
【8】周琦, 季根顺, 张建斌, 等. 管线钢中的硫化夹杂物与氢致开裂[J]. 材料工程, 2002, 30(9):37-39, 46.
【9】李丽锋, 张哲, 常大伟, 等. 某热煨弯管开裂原因分析[J]. 石油管材与仪器, 2019, 5(3):38-41.
【10】刘迎来. 小口径感应加热弯管低应力脆断原因分析及控制措施研究[C]//2015年全国失效分析学术会议论文集.[出版地不详]:[出版者不详], 2015.
【11】王勇, 冯大碧, 张力, 等. 管道硫化氢应力腐蚀破裂的原因分析[J]. 油气储运, 2004, 23(12):46-47, 60.
【2】叶帆, 杨伟. 塔河油田集输管道腐蚀与防腐技术[J]. 油气储运, 2010, 29(5):356-360, 364, 315.
【3】卢智慧, 何雪芹, 何昶. 塔河油田集输管道腐蚀因素及防腐措施[J]. 油气田地面工程, 2015, 34(7):18-20.
【4】赵震, 黄雪峰, 刘强. 塔河油田地面集输处理系统腐蚀穿孔原因[J]. 腐蚀与防护, 2013, 34(5):442-445.
【5】张志宏, 许艳艳, 葛鹏莉, 等. 塔河油田集输管线20#钢在CO2/H2S环境中的腐蚀行为[J]. 工业安全与环保, 2020, 46(1):32-36.
【6】陶勇. 金属材料应力腐蚀裂纹的探讨[J]. 中国教育技术装备, 2013(6):131, 134.
【7】潘卫军. 埋地管道材料的H2S应力腐蚀研究[D]. 南京:南京工业大学, 2004:1-3.
【8】周琦, 季根顺, 张建斌, 等. 管线钢中的硫化夹杂物与氢致开裂[J]. 材料工程, 2002, 30(9):37-39, 46.
【9】李丽锋, 张哲, 常大伟, 等. 某热煨弯管开裂原因分析[J]. 石油管材与仪器, 2019, 5(3):38-41.
【10】刘迎来. 小口径感应加热弯管低应力脆断原因分析及控制措施研究[C]//2015年全国失效分析学术会议论文集.[出版地不详]:[出版者不详], 2015.
【11】王勇, 冯大碧, 张力, 等. 管道硫化氢应力腐蚀破裂的原因分析[J]. 油气储运, 2004, 23(12):46-47, 60.
相关信息